Yamaha FIRMWARE UPDATING Process RX A3000 Update Version 3.50_Installation_Manual RXA3000 Installation Transmission

User Manual: Yamaha RX-A3000 Firmware Update Version 3.50_Installation_Manual

Open up the PDF directly:
View PDF
Yamaha Rx-a3000 Firmware Update but No Display
.
Page Count: 6

RX-A3000  FIRMWARE UPDATING PROCEDURE Important NOTICE Do not attempt to update your Yamaha receiver using any other information file except those provided directly from the Yamaha website or through your network connexion. Follow the instructions advisedly and exercise not effort any other procedures not specified in the instructions provided by Yamaha. Improperly updated products may cause improper performance, and whatever parts or service required to restore proper operation will not exist covered under the Yamaha Limited Warranty.  Choose from the following 2 methods to update to the latest firmware. Click here for Firmware  Update Through the Cyberspace  (Connection to the Net is required)  Click here for Firmware  Update by USB  (A USB thumb drive is required)  In case of error, run into the Troubleshooting section  ane  RX-A3000  Firmware Update Through the Internet Requirement:  Internet connectedness Your receiver is connected to the Net if you tin receive Cyberspace radio stations. (Meet possessor’s manual for details)  1 Power off the receiver (Standby mode) 2 Enter the Avant-garde SETUP mode While pressing the STRAIGHT button, press the MAIN ZONE push and keep STRAIGHT button pressed until “ A D V A Due north C E D S E T U P ” appears on the front panel display.  * “ A D V A Due north C E D South Eastward T U P ” is displayed just for a few seconds. ADVANCED SETUP  three Select “Business firm UPDATE” from the menu a. Press the Plan button until “ F I R M U P D A T E U Southward B ” is displayed. b. Then, press STRAIGHT push until “ N E T West O R 1000 ” is displayed. Firm UPDATE USB  FIRM UPDATE NETWORK  4 Start firmware update a. Press INFO button to commencement the update. (Update process may take up to xv minutes)  * If “ U P D A T E U N A V A I L ” appears, this means your receiver is already up-to-date. In this case, power off to exit from Avant-garde Setup. Your AV receiver is ready for normal apply. Firmware update in progress  NETWORK UPDATE  VERIFYING...  Sx-x:xx%  Caution DO Non interrupt power during the update. In case the power is accidentally cut off resulting in a condition where you can’t recover normal operation, refer to the troubleshooting method (Troubleshooting Example ii) on the last page. b. When completed, “ U P D A T Due east Due south U C C East S Southward ” appears on the display.  UPDATE SUCCESS c. Turn off the ability of the receiver by pressing the Principal ZONE button. STRAIGHT button MAIN ZONE push button Program push  2  INFO button  RX-A3000  5 Check the updated firmware version a. Power on the AV receiver and press the ON SCREEN button on the remote control. b. Select “Data” > “Arrangement”. c. Confirm that the firmware version is updated to the latest version. ON SCREEN button  Congratulations! You have completed the firmware update. Your AV receiver is set for normal use.  3  RX-A3000  Firmware Update by USB Requirement:  USB thumb bulldoze, with enough free space to store over 25MB. (File organisation with FAT16 or FAT32 format) Firmware file provided by YAMAHA,”RXV3067-xxxx.bin”.  1 Prepare USB thumb drive for the update Download the firmware, unzip and copy “RXV3067-xxxx.bin” into the root directory of the USB thumb drive.  Elevate & Drop the file into USB pollex bulldoze.  two Ability off the receiver (Standby manner) 3 Insert the USB thumb drive USB port is located at the lower left corner of the front console.  4 Enter the Avant-garde SETUP fashion While pressing the Straight button, printing the Chief ZONE push button and keep Direct button pressed until “ A D V A Northward C E D S Eastward T U P ” appears on the forepart panel display.  ADVANCED SETUP  v Select firmware update from the menu Printing the Plan button until “ F I R M U P D A T E U S B ” is displayed. Firm UPDATE USB  Direct button MAIN ZONE push button Plan push button USB port  4  RX-A3000  6 Get-go firmware update a. Press INFO button to commencement the update. (Update process may take up to 15 minutes)  * If “ U P D A T East U N A Five A I L ” appears, this means your receiver is already up-to-appointment. In this instance, power off to exit from Advanced Setup. Your AV receiver is set for normal use. Firmware update in progress  USB UPDATE  VERIFYING...  Sx-x:xx%  Caution Practise NOT interrupt power during the update. In case the ability is accidentally cutting off resulting in a condition where you can’t recover normal functioning, refer to the troubleshooting method (Troubleshooting CASE 2) on the last page. b. When completed, “ U P D A T E S U C C E Due south Due south ” appears on the brandish.  UPDATE SUCCESS c. Plow off the power of the receiver by pressing the Principal ZONE button. INFO button Chief ZONE push  USB port  7 Check the updated firmware version a. Power on the AV receiver and press the ON SCREEN button on the remote control. b. Select “Data” > “Organisation”. c. Ostend that the firmware version is updated to the latest version. ON SCREEN push button  Congratulations! You accept completed the firmware update. Your AV receiver is ready for normal employ.  v  RX-A3000  Troubleshooting Example ane “UPDATE FAIL” appeared during the update Crusade:  For some reason, the receiver can’t read the firmware information.  Method:  For your solution, check the post-obit  [Update through Internet] ❏ Check Internet connection. Your Internet connexion is working past playing an Net radio station. (See owner’southward transmission for details)  [Update past USB thumb drive] ❏ USB pollex drive is connected properly to the receiver. ❏ USB thumb drive is not password protected. (AV receiver cannot read data from a security protected USB thumb bulldoze)  ❏ Make sure the USB thumb bulldoze is inserted before the receiver is powered on for the update.  ❏ The firmware data, RX–V3067-xxxx.bin is stored in the root directory of the USB thumb drive.  ❏ At that place is no other data except the firmware information in the USB thumb drive. ❏ No folders are created in the USB pollex drive. Else, retry the update by USB using some other USB thumb drive.  CASE ii Firmware update doesn’t start for other reasons ● Receiver doesn’t ability upward after the update. ● Or, “ERROR” appeared when confirming the firmware version. Recovery method using USB method: 1. Unplug the AC ability cable from wall outlet. ii. Insert the USB thumb bulldoze which has the firmware data stored inside, into the USB port located on the front panel. 3. Press and hold the PURE Direct push button and keep it pressed while you plug the AC power cable back into the wall outlet again. “ U S B U P D A T Eastward ” will appear on the front end display. And so, release the PURE DIRECT push. four. The update will get-go automatically. 5. When “ U P D A T E S U C C E Due south Southward ” appears on the display, firmware update is completed. Power off the receiver and remove the USB pollex drive. vi. Confirm updated firmware version.  USB UPDATE  UPDATE SUCCESS PURE Direct button  USB port  6
      

Source Exif Information:

Read:  Update Firmware on Trek Wireless Outdoor Speaker

File Type                       : PDF File Type Extension             : pdf MIME Type                       : application/pdf PDF Version                     : one.half dozen Linearized                      : Yes Encryption                      : Standard V4.iv (128-bit) User Admission                     : Print, Copy, Extract, Impress high-res XMP Toolkit                     : Adobe XMP Core iv.0-c321 44.398116, Tue Aug 04 2009 14:24:39 Instance ID                     : uuid:fa175eb9-e1d3-4350-bdac-6760ce183d12 Certificate ID                     : uuid:C8F10648-C30D-E6AE-7595-02ECF6A9157C History Activeness                  : linearized, encrypted History Software Agent          : PDFlib PLOP 5.0 (.Internet/Win64), PDFlib PLOP 5.0 (.Cyberspace/Win64) History When                    : 2016:11:25 18:43:14+09:00, 2016:11:25 18:43:14+09:00 Producer                        : Acrobat Distiller 8.2.six (Windows) Creator Tool                    : Adobe InDesign CS3_J (5.0.iv) Alter Date                     : 2016:11:25 18:43:fourteen+09:00 Create Date                     : 2011:06:26 fifteen:04:59+09:00 Metadata Engagement                   : 2016:eleven:25 18:43:14+09:00 Format                          : application/pdf Championship                           : FIRMWARE UPDATING Procedure Creator                         : YAMAHA CORP. Clarification                     : RX-A3000 Page Count                      : half dozen Folio Layout                     : SinglePage Bailiwick                         : RX-A3000 Writer                          : YAMAHA CORP.
      

EXIF Metadata provided by
EXIF.tools