Tevo Tarantula Community Firmware U8glib.h: No Such File or Directory

Tevo Tarantula Community Firmware U8glib.h: No Such File or Directory

              TEVO Tarantula 3D printer Installation Guide
            

TEVO Tarantula 3D printer Installation Guide

READ ME Offset

READ THIS MANUAL COMPLETELY BEFORE ASSEMBLING AND POWERING UP YOUR PRINTER!

Hazards and Warnings

The TEVO Tarantula 3D printer has motorized and heated parts. When the printer is in operation e’er be aware of possible hazards.

Electrical Daze Hazard

Never open the electronics bay of the printer while the printer is powered on. Before removing the access door, always power down the printer and unplug the AC line cord.

Burn Hazard

Never touch the extruder nozzle, heater block, or the heated bed without first turnnig off the hotend (or heated bed) and allowing it to completely cool down. The hotend (or heated bed) tin can take up to twenty minutes to completely cool down. Besides, never touch recently extruded filaments. The filament can stick to your pare and causes burn.

Burn Hazard

Never place flammable materials or liquids on or well-nigh the printer when powered on or in operation. Liquid acetone and vapours are extremely flammable.

Compression Hazard

When the printer is in operation, exist careful never to put your fingers in the moving parts, including the belts, pulleys, gears, wheels or leadscrews.

Static Charge

Make sure to ground yourself earlier touching the printer, specially the electronics Electrostatic charges tin can harm electronic components. To footing yourself, affect a grounded source.

Age Warning

For user nether the ages of 18, adult supervision is recommended. Beware of choking hazards around children.

Alphabetic character from TEVO

Dearest Customer,
Thank you for purchasing the TEVO Tarantula 3D printer.
This guide will step you through the assembly and the showtime run of the printer. If you have any problems during assembly, delight go to our Facebook group:
https://world wide web.facebook.com/groups/TEVO.3dprinter.owners/

If you cannot resolve your trouble at that place, practice not hesitate to contact us through the website
http://support.tevoprinter.com/

Please make sure that the frame is completely square and tight in every bending by using a gemmetrical triangle or any other more sophisticated square tools (not supplied with the printer kit.)
Regards,
TEVO Team

Assembly

  1. Remove the parts from the box and remove any record and padding from the parts. Inspect the parts to make sure they were non damaged in shipment.
  2. Install the gantry frame (A) to the base frame (B).
    • On the gantry frame, brand certain the nozzle assembly is to the front. On the base frame, make sure the steppeer motor is on the dorsum.
    • Use the M5x25 screws (4 pcs) and lock washers (four pcs). Heighten the base of operations frame above the tabular array. Install the screws through the base frame into the threaded holes in the gantry frame (equally shown in picture below). Tighten with M5 hex key (Allen) wrench.

TEVO Tarantula 3D printer Installation Guide-Assembly

3. Install the two T-shaped frame reinforcement plates. The plate with the limit switch goes on the Z stepper motor side.
• Loosen the T-nuts by mitt and plough them so they volition fit within the grooves on the frames. Continue the nuts loose so that when you tighten the bolts, the basics volition rotate 90 degress and grab onto the inside of the groove.
• Tighten all eight bolts using the M5 hex key (Allen) wrench.

TEVO Tarantula 3D printer Installation Guide-Tighten all eight bolts using the M5 hex key (Allen) wrench

4. Connect all electric cables.
• Put the control box on the lead screw side of the printer with the screen facing frontwards.
• Connect the heater cables to the command box.
The cablevision for the build pates has four pins. The cable for the nozzle heater has 8 pins. Rotate the connector until the pins slide easily into the socket. Do NOT force them.
Afterward the pins are fully inserted, manus-tighten the knurled nuts so they don’t become unplugged.
• Connect the stepper motor and limit switch cables.
The Y cables go to the stepper motor and limit switch at the back of the base frame.
The Z cables go to the stepper motor and limit switch on the atomic number 82 screw side of the base frame. The Ten and Due east (extruder) cables go to the gantry frame. The X cables get to the stepper motor and limit switch that runs the belt and the E cables go to the stepper motor that drives the extruder.
• Connect the ability cord to the dorsum of the control box and to a standard 220v/110v electrical outlet.
• Plow the power on using the switch on the back of the control box.

Read:  Cara Flash Samsung Galaxy Star

TEVO Tarantula 3D printer Installation Guide-Turn the power on using the switch on the back of the control box

v. Make sure the PTFE tube is all the fashion down in the hot end, information technology may come up loose during transportation. Push it down all the fashion into the hotend. Gaps between PTFE tube and nozzle will crusade clogging.

TEVO Tarantula 3D printer Installation Guide-Make sure the PTFE tube is all the way down in the hotend

Fine-Tuning

1. Adjust the tension of the build plate wheels on the Y-axis on the base of operations frame.
• Bank check the tension of the build plate wheels. Try to turn the wheels nether the build plate without forcing it. If the wheel turns freely or without much attempt, then it is as well loose.
• To tighten the wheels, rotate the eccentric nut that connect to the wheel. Utilise the open terminate wrench to rotate the basics slightly until the wheels is snug against the Y-axis frame.
• The build plate assembly and the belt should move forrad and backward without much endeavor, and in that location should have no side-to-side jerk or play.

TEVO Tarantula 3D printer Installation Guide-Fine-Tuning

2. Adjust the tension of the gantry wheels on the correct pillar of the gantry frame.
• Check the tension of the gantry plate wheels. Attempt to plow the wheels behind the plate without forcing it. If the cycle turns freely or without much attempt, information technology is too loose.
• To tighten the wheels, rotate the eccentric nut that connect to the wheel. Use the openend wrench to rotate the nut slightly until the wheel is snug against the Z-axis.

TEVO Tarantula 3D printer Installation Guide-o tighten the wheels, rotate the eccentric nut that connect to the wheel

3. Adjust the tension of the Ten-carriage wheels on the X-axis on the gantry frame.
• Bank check the tension of the 10-wagon wheels. Try to turn the wheels nether the build plate without forcing information technology. If the wheel turns freely or without much effort, then it is too loose.
• To tighten the wheels, rotate the eccentric nut that connect to the wheel. Use the open end wrench to rotate the nuts slightly until the wheels is snug against the Ten-axis frame.
• The hotend assembly and the belt should motion left and right without much try, and at that place should have no front-and-dorsum wiggle or play

TEVO Tarantula 3D printer Installation Guide-Fine-The hotend assembly and the belt should move left and right without much effort

4. Bank check the tension of the chugalug driving the Y-axis (under the build plate). The chugalug should exist taut, with no slack or slop.
• If the chugalug is loose:
• Loosen the four bolts at the front of the base frame holding the belt caster.
• Pull the caster to tighten the belt. Belongings the chugalug taut, tighten the iv bolts.

TEVO Tarantula 3D printer Installation Guide-Pull the pulley to tighten the belt. Holding the belt taut, tighten the four bolts

5. Check the tension of the belt driving the X-railroad vehicle. The belt should be taut, with no slack or slop.

  • If the chugalug is loose:
  • Loosen the two bolts at the right side of the gantry property the belt pulley.
  • Pull the pulley to tighten the chugalug. Property the chugalug taut, tighten the 2 bolts.

TEVO Tarantula 3D printer Installation Guide-Pull the pulley to tighten the belt. Holding the belt taut, tighten the two bolts

6. Arrange the tension on the Titan Extruder with the screw shown in the moving-picture show below if the filament doesn’t come out smoothly during print.

TEVO Tarantula 3D printer Installation Guide-Adjust the tension on the Titan Extruder with the screw shown in the picture below

Leveling the Build Plate

To build skilful parts, the build plate needs to exist level, and the nozzle needs to be about 0.1mm from the build plate in all locations. This is about the thickness of a unmarried piece of A4 paper. Yous want to adjust the elevation of the build plate so thate you can barely slide the newspaper between the nozzle and the build plate with only a picayune resistance.

  1. Select
    Gear up -> Preheat PLA. This will rut up the bed and the nozzle to actual printing weather condition, making the leveling more accurate.
  2. Select
    Prepare -> Auto home. This will movement the nozzle to the home position at the front end left corner of the build plate.
  3. Select
    Gear up -> Disable steppers. This will allow y’all to move the X-carriage and build plate by hand.
  4. Tips: The Z-axis stepper motor is too disabled, and you don’t desire it to move at all. And so y’all should handle the printer gently during the leveling process. Proceed it apartment and move the X-railroad vehicle carefully.
  5. Wait for the print bed and nozzle temperature to reach the target temperature. The info screen displays this information below the nozzle and bed icons.
  6. Slide a piece of paper between the nozzle and the build plate.
  7. Adust each of the 4 thumbscrews under the bed until the slice of paper slides, with just a bit of drag, in all locations on the build plate.

  8. You may need to brand fine adjustments to the bed level when yous kickoff printing. The first layer of the impress will evidence whether the distance between the nozzle and the build plate is correct. You want it to be pushed into the build surface slightly to maximize surface expanse contact while still allowing good extrusion flow.
    • You can attempt to carefully arrange the thumbscrews during the offset layer of the print while the plate is moving until the distance betwixt the nozzle and the build plate is producing smooth extruded lines.
    • Afterward you have fine-tuned the bed level during the get-go layer, you may want to finish the print, articulate the build plate, and restart the print.
Read:  Cara Membuka Pola Hp Yang Lupa Tanpa Menghapus Data

Preparaing Slicing Software

This printer works with most slicing/printing software similar Simplify3D, Cura, Repetier-Host, etc. But nosotros will go in details for Repetier-Host software and tell you lot how to gear up it up then that yous can make your start print. Get-go we recommend you to download the software from the official website:
https://www.repetier.com

Later installation is done and you start the software, y’all should get the following screen:

TEVO Tarantula 3D printer Installation Guide-After installation is done and you start the software, you should get the following screen

Now we have to fix our printer in the settings so that Repetier-Host tin can connect to information technology and will know what size of build area our printer use. Open the Printer Settings window (click Config -> Printer Settings).

Starting time set
Port
to whatever port your mainboard uses (when you take connected your printer to PC it should show up in hither). Set
Baud Charge per unit
to 250000 and DO Not touch whatever other settings in this tab (see picture show in adjacent page.)

TEVO Tarantula 3D printer Installation Guide-First set Port to whatever port your mainboard uses

Click on
Printer Shape
tab, change the following values:
Ten Max – 320
Y Max – 320
Print Surface area Width – 300
Print Area Depth – 300
Print Area Tiptop – 400

TEVO Tarantula 3D printer Installation Guide-Click on Printer Shape tab

Go to Printer tab, change the value according to the pic on the left.

TEVO Tarantula 3D printer Installation Guide-Go to Printer tab, change the value according to the picture on the left

Go to
Slicer
tab, select
Slic3r
as slicer and click on
Configuration.

TEVO Tarantula 3D printer Installation Guide-Go to Slicer tab, select Slic3r as slicer and click on Configuration

TEVO Tarantula 3D printer Installation Guide-Go to Slicer tab, select Slic3r as slicer and click on Configuration 2

On Slic3r window, go to File -> Load Config. (Loaded setting is for full general PLA filament press).
Select and load Tornado.ini from SD card.
Rename impress setting, filament, printer to Tornado and save.

How to Piece 3D Object for SD Print

Click on Load, browse to location of the file, and then choose Open.

TEVO Tarantula 3D printer Installation Guide-Click on Load, browse to location of the file, then choose Open

Afterward the file is open in 3D view, click on Slicer tab to go into slicing page.

TEVO Tarantula 3D printer Installation Guide-After the file is open up in 3D view, click on Slicer tab to go into slicing pageSelect the correct Print Setting, Printer Settings, and Extruder blazon, then click on Slice with Slic3r.

TEVO Tarantula 3D printer Installation Guide-Select the correct Print Setting, Printer Settings, and Extruder type, then click on Slice with Slic3r

After slicing, click on Salve for SD Impress to save the G-lawmaking file to the SD carte with file name of your choice. And so yous tin insert the card to your printer and choose Impress from SD to start printing.

TEVO Tarantula 3D printer Installation Guide-After slicing, click on Save for SD Print to save the G-code file to the SD card with file name of your choice

How to Wink Firmware

To install firmware on your printer, you’ll need to download the following:

  1. Arduino IDE (http://world wide web.arduino.cc)
  2. Firmware Source Code (You tin can become it from many means, due east.thousand. our Facebook Page Files section, our Customer Service, or from Marlin and Repetier directly.)

In this affiliate, we’re going to use Marlin for demonstration.

Configuration
Firmware downloaded from our Facebook page or from our customer service are pre-configured, you tin use it without any modification.
To configure, you’ll need to edit 2 files:
configuration.h
and
configuration_adv.h. Yous can visit their website for explanations of the configuration file format and a synopsis of nearly of the options in these files.

Read:  Samsung C5 Official Firmware Blocked by Frp

Verify / Compile
To start the procedure, practise the following steps:

  1. Double-click
    Marlin.ino
    file to open up it in Arduino IDE.
  2. Select
    Arduino/Genuino Mega or Mega 2560
    from
    Tools
    ->
    Boards
    menu.
  3. Select the serial (USB) port that your lath is continued to in
    Tools
    ->
    Serial Port menu
    .
  4. Click the
    Verify/Compile
    push button at the summit of the window to brand sure there are no configuration errors. (Or you lot tin click on
    Upload
    push button adjacent to Verify/Compile if yous’re using Marlin from our Facebook folio or our customer service).
  5. In one case all errors are fixed, go along with the upload by clicking
    Upload
    button. A blue or green LED on the board will flash rapidly during this procedure.

Flash Your Board
To flash your board, practise the following steps:

  1. Ensure Marlin.ino is open in the Arduino IDE.
  2. Select Arduino/Genuino Mega or Mega 2560 from
    Tools
    ->
    Boards
    menu.
  3. Select the series (USB) port that your board is continued to in
    Tools
    ->
    Serial Port
    carte du jour.
  4. Click on Upload button to begin flashing your controller board. A blue or dark-green LED on the board will flash apace during this process.

That’southward it! Now you’ve flashed firmware to your board, enjoy printing!

TEVO Later-Sales

Honey Customer,
Give thanks you for purchasing TEVO 3D printer. Nosotros are defended to producing low price, high quality 3D printers and hope you have as much fun using it every bit we did creating it!
If you have any issue/questions regarding the contents in the kit, delight fill out a Service Ticket on our Support page.
http://support.tevoprinter.com


qr code

Creating a Service Ticket will serve equally your official asking for TEVO support. Our Customer Back up Team will contact y’all inside
48 hours.

SERVICE Data:

1. REPLACEMENT PARTS

1.one. TEVO products are covered nether a Replacement Office Plan for a period of 12 months from the date of purchase.
ane.2. Missing/Damaged/Defective Parts
1.2.i. Within vii days of the delivery date, TEVO volition supplant any parts gratis of charge including shipping fees.
1.two.2. Later 7 days of the delivery date, TEVO will replace whatever parts costless of charge Simply the customer volition be responsible for aircraft fees.
one.3. Customer Damaged Parts
one.3.1. The client shall pay for the cost of the parts AND the shipping fees.

2. CARRIER LOSS, MIISSING, DAMAGED, AND DEFECTIVE PARTS

ii.1. Claims for lost or damaged shipments must exist reported to the carrier within the carrier’s claim window, the customer needs to inform TEVO within
vii days
of the commitment appointment.
2.1.1. For whatsoever parts lost or damaged during shipping, the client shall take photos or video and submit them when filling out a Service Ticket. If a claim number was issued by the carrier, please include the claim number when creating your Service Ticket
(Study a Problem / Carrier Lost Parts.)

2.one.2. Once the Carrier dispute is resolved, delight provide TEVO with all communications with the carrier. It is the customer’south responsibility to keep TEVO up to date with ALL communications with the carrier.
2.1.three. TEVO volition work with the client on replacing the parts in the merits.

2.2. For Missing Parts, refer to section 1.2, the customer shall fill out a Service Ticket (Study a Problem / Missing Parts.)
ii.3. For Damaged Hardware Parts, refer to section 1.ii, the customer shall take photos or video and submit them when filling out a Service Ticket (Report a Trouble / Damaged Hardware Parts.)
2.4. For Lacking Electronic Parts, refer to section i.ii, the client shall take photos or video and submit them when filling out a Service Ticket (Study a Problem / Defective Electronic Parts.)

2.4.1. If the office is the LCD Panel, Power Supply or Mainboard, the customer shall transport the part back to TEVO and TEVO will ship a new office.

2.5. For parts damaged by the customer, refer to section 1.3, submit a Service Ticket (Report a Problem / Customer Damaged Parts.)

3. General SUPPORT

For data and support on edifice and operating your TEVO Tornado 3D printer, delight visit the TEVO Tornado Owners Grouping.
https://www.facebook.com/groups/TEVO.Tornado.Owners/


qr code

Tevo logo

Documents / Resource

References

Tevo Tarantula Community Firmware U8glib.h: No Such File or Directory

You May Also Like