Sonicwall Boot Uploaded Firmware With Backup Settings

Sonicwall Boot Uploaded Firmware With Backup Settings



04/05/2022



3,380
People found this article helpful



137,325
Views

Description

This commodity describes how to put a SonicWall into safe way through the GUI or through the command line interface (CLI). This article will also detail how to upgrade the firmware or the ROM version while in safe mode every bit these are the two most common configurations performed using rubber mode.

Cause

Putting the SonicWall into safe style is nigh ordinarily required in the following instances.

  • Upgrading the firmware without access to the GUI/CLI.
  • Upgrading the ROM version.
  • Viewing the bootlogs or other diagnostic information.
  • Attempting to gain access to an unresponsive device.

Resolution

Putting the SonicWall into Safe Style

  1. Using a paperclip or similarly sized object, printing and concord down the RST button located in the small hole on thursday front end of the device for at least 60 Seconds. Once the exam light on the device becomes solid or begins to blink then the SonicWall is in condom mode.


    NOTE:
    Some SonicWall Models, such as certain TZs, take the RST push located on the back of the device. Consult the administration or hardware guide for your specific SonicWall Model if you’re unsure. On an NSsp 13700 or NSa Series appliance, press the push button, merely you do not demand to hold it down.

  2. Connect a estimator directly to the following Interface, depending on what model SonicWall you take, via an ethernet cablevision.


    Generation 5: X0 Interface.

    Generation 6 (SonicWall NSA or SuperMassive): Direction Interface.
    Generation half dozen (SOHOW, TZ series): X0 Interface
    Generation 7 (NSsp 13700 or NSa): Direction Interface.
    Generation 7 (TZ series): X0 Interface

  3. Manually assign a static IP / subnet mask on the continued computers NIC depending on what model SonicWall you have.


    Generation v: 192.168.168.20 | 255.255.255.0.

    Generation half-dozen (SonicWall NSA or SuperMassive): 192.168.1.20 | 255.255.255.0.
    Generation 6 (SOHOW, TZ series): 192.168.168.20 | 255.255.255.0.
    Generation seven (NSsp 13700 or NSa): 192.168.1.20 | 255.255.255.0.
    Generation 7 (TZ serial): 192.168.168.20 | 255.255.255.0.

  4. Open up a Web browser and navigate to the post-obit URL, depending on what model SonicWall you have.


    Generation five: 192.168.168.168.  (https://192.168.168.168.)

    Generation 6 (SonicWall NSA or SuperMassive): 192.168.1.254.  (http://192.168.1.254.)
    Generation vi (SOHOW, TZ series): 192.168.168.168. (https://192.168.168.168.))
    Generation 7 (NSsp 13700 or NSa): 192.168.1.254. (http://192.168.1.254.))
    Generation 7 (TZ series): 192.168.168.168 (https://192.168.168.168.))

  5. You should now be on the condom mode GUI and take the following options.



    NOTE:
    For new safe mode options on Gen7, please refer:
    Safemode options on SonicWall Gen 7 devices



Gen 7 (Using SafeMode to Upgrade Firmware):

  1. Once we enter the url in the spider web browser (Step-4) to get to
    the safe mode page on SonicWall Gen 7 devices, we need to authenticate using Maintenance Fundamental.
  2. In the Maintenance Key prompt, type in or paste the cardinal y’all got from MySonicWall and so click Authenticate. If your appliance is running SonicOS seven.0.1 and is not however registered, use its Auth Lawmaking equally the primal. (To notice the Maintenance cardinal, please refer to:
    Safemode options on SonicWall Gen vii devices)
    Image

  3. Safe mode page is displayed

    Image

  4. Click Upload Image, and and so browse to the location where you saved the SonicOS firmware image, select the file, and click Upload.
  5. Click the Kick push button in the row for Available Image Version and select one of the following:

    Kicking Available Image with Current Configuration:
    Use this option to restart the appliance with your electric current configuration settings.

    Boot Available Image with Manufactory Default Configuration:
    Utilize this option to restart the appliance with manufacturing plant default configuration settings. The configuration settings revert to default values, but logs and local backups remain in place.

    Kick Bachelor Image with Backup Configuration:
    Use this option to restart the appliance with saved backup configuration settings. You tin can cull which backup to use.

    Image

  6. . In the confirmation dialog, click Kicking to proceed.
  7. Look while the firmware is installed, so booted.
  8. Login to the SonicWall direction GUI as you normally would.
Read:  Asus Router Admin Page Won't Load After Firmware Update



Putting the SonicWall into Rubber Style via the CLI



Annotation:
At that place is an East-CLI control
safemode
that restarts the firewall in SafeMode for Generation vii (NSsp 13700 or NSa).

  1.  If you lot’re unfamiliar with how to admission the SonicWall management using CLI please referenceHow to login to the appliance using the Command Line Interface (CLI).
  2. One time logged into the CLI, input the following commands.


    Safemode

    aye

  3. The SonicWall will reboot and enter safe mode.
    Image
  4. Reference the steps above to login to the rubber mode GUI, beginning with“Connect a estimator directly to the post-obit Interface…”



Upgrading the Firmware or ROM Version from Prophylactic Way

  • Download the desired firmware version from MySonicWall.com or accept the desired ROM Version on hand. ROM Packs are only available via SonicWall technical support.


    Annotation:
    Upgrading the ROM version but applies to Generation 6 NSA SonicWalls – 2600, 3600, 4600, 5600, and 6600. Unless you accept been requested to upgrade the ROM version by SonicWall technical support exercise not endeavor to practice so.

  • SelectUpload New Firmware and follow the prompt in the pop-up window to upload the firmware or ROM version to the SonicWall.
  • Yous should at present see the
    New Firmware or Uploaded ROM Pack
    on the safe mode GUI. You tin can boot to the new firmware or ROM by clicking the boot icon on the far right.


    Annotation:
    Booting to a new firmware or ROM version will reboot the SonicWall and exit safe mode. Make sure you’re completely finished with the SonicWall’s safe mode before selecting boot.

  • After the reboot, login to the SonicWall direction GUI as y’all normally would. Navigate toMonitor | Current Status
    | System Condition.
  • On the
    Status
    screen you should come across the new firmware version listed underFirmware Versionor the new ROM version listed underSafemode Version.

    Image

Read:  Galaxy Note 4g-lte; Model: Shv-e160l Firmware Download

Related Manufactures

Categories


Was This Article Helpful?


Yes


NO

Commodity Helpful Form

Article Not Helpful Form

Sonicwall Boot Uploaded Firmware With Backup Settings

You May Also Like