Qnap Nas 4.3.4 Not Show Firmware Update

Qnap Nas 4.3.4 Not Show Firmware Update


Firmware Recovery Guide for ARM based NAS


Applied QNAP NAS models

For firmware update of QNAP TS-110, TS-112, TS-119, TS-210, TS-212, TS-219, TS-219P, TS-410, TS-410U, TS-412, TS-412U, TS-419P, TS-419U, TS-419U+, TS-119P+, TS-219P+, TS-419P+, TS-120, TS-121, TS-220, TS-221, TS-420, TS-421, TS-420U, TS-421U Turbo NAS servers via recovery mode.


When to use the firmware recovery guide


This firmware recovery guide is intended for users who encounter arrangement startup failure due to incomplete or unsuccessful firmware update caused by ability outage or network disconnection during the process. To verify if this guide applies to your NAS, follow the steps below:

one. Power off the NAS.
2. Remove all the hard disks.
3. Power on the NAS.
4. Wait for ten seconds and bank check if y’all hear a curt beep.
five. After the brusk beep, wait for two minutes to check if you hear a long beep.
6. If you merely hear a short beep or do not hear whatever beep, follow the instructions of this guide to recover your NAS.



Instructions for NAS Recovery – Method 1 (VMware Role player)


Follow the steps below to recover the NAS.

1. Download the live CD ISO image from the following links:

     For all TS-x10, TS-x12, TS-x19, TS-x20, TS-x21 series, delight utilize the folloiwng link:
http://eu1.qnap.com/Storage/tsd/live_cd/live-cd-20130730.iso

     For TS-112P, TS-212P, TS-212E and HS-210, please apply the following link:
http://eu1.qnap.com/Storage/tsd/live_cd/live-cd-20140212.iso

two. Download and install VMware Role player:
http://www.vmware.com/get/downloadplayer/

three. Disconnect whatsoever wireless network connections on your PC

4. Run VMware Player, and click on “Create a New Virtual Machine”


Qnap Nas 4.3.4 Not Show Firmware Update

5. Select “Installer disc epitome file (iso)”, and choose the ISO file downloaded in Footstep ane. Click “Adjacent”


RTENOTITLE

half dozen. Select “Linux” and “Ubuntu”, click “Adjacent”


RTENOTITLE

seven. For virtual automobile name and deejay settings, click “Adjacent”.

eight. Click “Customize Hardware”


RTENOTITLE

ix. Under “Network Adapter”, select Network Connectedness as “Bridged”, then click “Close”


RTENOTITLE

10. Click “Finish”. The virtual machine will start booting in a window. (If you get a message nigh software updates, click “Remind Me Later”)

11. When the login prompt is shown, go to next footstep.
No login is required.

12. Ability off the NAS and remove all hard disks.

13. Connect the NAS to the PC directly by an Ethernet cablevision.

If your NAS includes two LAN ports, delight connect LAN 2 of the NAS to the PC. If it doesn’t work effort it again with LAN 1

fourteen. Find the RESET button of the NAS (see beneath).


RTENOTITLE

xv. Employ a pen or whatever pointed object to printing and concord the RESET button.  Then press the Power button on the front panel to power on the NAS at the meanwhile.

16. Please go along holding the RESET push button and Ability push button until you hear two short beeps in about 5-8 seconds. The Condition LED of the NAS should be flashing red and greenish and then glows scarlet.

17. The LED on the LAN port of the NAS should be flashing for the starting time few seconds and then glows dark-green or orange.

eighteen.

Exit THE NAS Lone AT THIS POINT! DO Non TURN IT OFF OR UNPLUG THE POWER CORD. Look for about 5 minutes.

      Annotation: To make sure if the data has been delvering to NAS or non, you can login to the console by the username and countersign, root/root. And so, use the command “ifconfig” to see if the number of TX on eth0 is increasing or not.

19. Wait until yous hear a long beep or two brusk beeps and see the Status LED flashing green. The NAS will and then reboot. No intervention required during this stage.

twenty. The reboot should take near three minutes. Subsequently that you should hear a long beep.

21. Connect the NAS to your switch or router and use QNAP Finder to observe the NAS.

22. Power off the NAS, plug the HDD(s) dorsum by original guild, then ability it on.

23. Download the latest firmware from QNAP website(http://www.qnap.com/), unzip the file, and perform firmware upgrade through QNAP Finder.

24. On QNAP Finder, select the NAS, click Tools -> Update Firmware to update the NAS firmware.


What to practise if the startup problem persists


If the startup problem persists, delight return the NAS to your local dealer or distributor for system repair immediately.

Note: If the recover progress does non work at the first time, delight attempt another PC and make sure all other network connections are disabled. If the number of TX on eth0 is not increasing, please use some other Ethernet cablevision.



Instructions for NAS Recovery – Method two (Alive CD)


Follow the steps beneath to recover the NAS.

1. Download the live CD ISO image from the following links and “BURN” it into an empty CD-R.

    For all TS-x10, TS-x12, TS-x19, TS-x20, TS-x21 serial, please use the folloiwng link:


http://eu1.qnap.com/Storage/tsd/live_cd/alive-cd-20130730.iso

    For TS-112P, TS-212P, TS-212E and HS-210, delight use the following link:

http://eu1.qnap.com/Storage/tsd/live_cd/live-cd-20140212.iso

ii. Burn the ISO file to a CD.

iii. Insert the CD to a PC and boot up from the CD.

four. When the login prompt is shown, go to adjacent step.
No login is required.

five. Power off the NAS and remove all difficult disks.

6. Connect the NAS to the PC straight by an Ethernet cablevision.

If your NAS includes two LAN ports, please connect LAN 2 of the NAS to the PC. If it doesn’t piece of work try it over again with LAN 1

7. Find the RESET push button of the NAS (meet below).


RTENOTITLE

eight. Use a pen or any pointed object to press and concord the RESET button.  And so press the Power button on the front end panel to ability on the NAS at the meanwhile.

9. Please keep property the RESET button and Power push until you hear two brusk beeps in most five-eight seconds. The Condition LED of the NAS should exist flashing red and dark-green and then glows ruddy.

10. The LED on the LAN port of the NAS should be flashing for the first few seconds and so glows green or orange.

11.

Leave THE NAS Solitary AT THIS Betoken! Do Non Plough Information technology OFF OR UNPLUG THE POWER CORD. Wait for about 5 minutes.

Note: To make sure if the data has been delvering to NAS or non, you can login to the console by the username and password, root/root. And then, use the command “ifconfig” to see if the number of TX on eth0 is increasing or not.


12. Wait until you hear a long beep or two brusk beeps and run into the Status LED flashing green. The NAS will then reboot. No intervention required during this stage.

thirteen. The reboot should take nearly 3 minutes. After that y’all should hear a long beep.

14. Connect the NAS to your switch or router and employ QNAP Finder to find the NAS.

fifteen. Ability off the NAS, plug the HDD(due south) back by original social club, then power it on.

xvi. Download the latest firmware from QNAP website(http://www.qnap.com/download.asp), unzip the file, and perform firmware upgrade through QNAP Finder.

17. On QNAP Finder, select the NAS, click Tools -> Update Firmware to update the NAS firmware.


How to practise if the startup problem persists


If the startup problem persists, please render the NAS to your local dealer or distributor for system repair immediately.

NOTE: If the recover progress does not piece of work at the first time, please try another PC or reburn the ISO epitome.


Firmware Recovery Guide for x86-based NAS


Applied QNAP NAS models

TS-239 Pro, TS-239 Pro II, TS-239 Pro Two+, TS-439 Pro, TS-439 Pro Two, TS-439 Pro Two+, TS-259 Pro, TS-259 Pro+, TS-459 Pro, TS-459 Pro+, TS-459 Pro II, TS-459U, TS-459U+, TS-559 Pro, TS-559 Pro+, TS-559 Pro II, TS-639 Pro, TS-659 Pro, TS-659 Pro+, TS-659 Pro Two, TS-859 Pro, TS-859 Pro+, TS-859U, TS-859U+, TS-509, TS-809, TS-809U, SS-439, SS-839, HS-251, HS-251+, TS-x51 Series, TS-x51+ Series, TS-x51U Series, TS-453mini, TS-x53 Series


When to utilise the firmware recovery guide


This firmware recovery guide is intended for users who encounter organization startup failure due to incomplete or unsuccessful firmware update acquired by ability outage or network disconnection during the process. To verify if this guide applies to your NAS, follow the steps below:

1. Power off the NAS.
2. Remove all the hard disks.


RTENOTITLE


3. Connect the NAS with a VGA/HDMI monitor and a USB keyboard.


RTENOTITLE


4. Power on the NAS

“AMI BIOS …”–> the post-obit screen shows the BIOS can startup correctly
“1023MB OK” –> DRAM has been detected (DRAM size is depend on NAS model)
“128MB ATA Flash Disk ADAA408J” –> DOM has been detected (DOM size is depend on NAS model)

RTENOTITLE

Read:  Firmware, or Else Your Segway Will Lean Backwards While Driving Full Speed

If the BIOS cannot be started or whatsoever component cannot be detected correctly, similar DRAM, DOM, y’all need to contact with local distributor and

send back the NAS for repair
. If the NAS system can exist startup correctly after HDD removed, you will

demand to replace the HDD

as the startup failed issue should exist caused past HDD.

five. When the screen will show “Uncompressing Linux…” .


RTENOTITLE

At this phase, the system on the DOM is starting to boot up. Withal, if the organization is corrupted, some error message might occur on the screen during the startup process. You can endeavor to

recover the arrangement on the DOM by post-obit steps
.

six. To recover the system on the DOM, you demand follow the stride A and step B.

    A. Create a USB boot disk
B. Use the USB boot disk to refresh the organisation on the DOM.

Instructions for NAS Recovery


A. How to create a USB boot disk.


ane. Download the unetbootin utility and iso file from the link below:
http://unetbootin.sourceforge.internet/
– due east.g. please select “Download for windows” if yous are using Windows platform on your PC.
http://distro.ibiblio.org/damnsmall/current/dsl-iv.4.10-initrd.iso

2. Plug a USB flash drive to your PC. The USB wink drive should be 1GB or 2GB. Please format the USB flash bulldoze as FAT32.

RTENOTITLE

three. Install and run the unetbootin utility on your PC. Then select “Damn Modest Linux” for Distribution.
iv. Select “Diskimage”, and choose the iso file downloaded in step 1.
five. Make sure the Type is on “USB Bulldoze”, and click “OK” to install the kick system on the USB bulldoze.

RTENOTITLE

6. Click “Exit” afterward process completed.
7. Check your NAs model and download the system full image from the link below.
8. Copy organisation image file to the root folder of USB flash drive and rename the file to “dom.img”.

Download System Total Image

========================================================
TS-239 Pro
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-239_20091014-3.ane.two.img


TS-239Pro II
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-239PROII_20100928-1.0.six.img


TS-239 Pro Ii+
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-239PROII+_20110609-1.1.4.img


TS-259 Pro, TS-259 Pro+
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-259_20110609-1.i.4.img

TS-439 Pro
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-439_20091014-3.1.2.img


TS-439 Pro II
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-439PROII_20100928-1.0.6.img


TS-439 Pro II+
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-439PROII+_20110609-ane.i.4.img


TS-439U
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-439U_20091014-3.one.ii.img


TS-459 Pro, TS-459 Pro+, TS-459 Pro II
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-459_20110609-one.1.4.img


TS-459U, TS-459U+
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-459U_20110609-ane.1.4.img

TS-469 Pro, TS-469L
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-469_20140516-1.2.8.img

TS-469U-RP
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-469U_20140516-one.2.8.img


TS-509 Pro
http://eu1.qnap.com/Storage/tsd/fullimage/TS-509PRO.img


TS-559 Pro, TS-559 Pro+, TS-559 Pro Ii
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-559_20110609-1.ane.4.img

TS-569 Pro, TS-569L
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-569_20140516-1.2.8.img


TS-639 Pro
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-639_20091014-3.1.ii.img


TS-659 Pro, TS-659 Pro+, TS-659 Pro II
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-659_20110609-i.ane.4.img

TS-669 Pro, TS-669L
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-669_20140516-1.2.8.img


TS-809 Pro
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-809_20101119-1.0.ix.img


TS-809U
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-809U_20101119-1.0.9.img


TS-859 Pro, TS-859 Pro+
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-859_20110609-1.1.4.img


TS-859U, TS-859U+
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-859U_20110609-1.1.4.img

TS-869 Pro, TS-869L
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-869_20140516-one.ii.viii.img

TS-869U-RP
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-869U_20140516-1.2.eight.img

TS-1269U-RP
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-1269U_20140516-i.2.eight.img


SS-439
http://eu1.qnap.com/Storage/tsd/fullimage/F_SS-439_20090627-iii.ane.0.img


SS-839
http://eu1.qnap.com/Storage/tsd/fullimage/F_SS-839_20091014-3.1.2.img

HS-251
http://eu1.qnap.com/Storage/tsd/fullimage/F_HS-251_20140711-1.2.8.img

HS-251+
http://eu1.qnap.com/Storage/tsd/fullimage/F_HS-251_20150605-1.3.0.img

TS-x51 Series
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X51_20140916-1.2.viii.img

TS-x51+ Serial
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X51_20150605-one.3.0.img

TS-x51U Series
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X51U_20141128-1.2.viii.img

TS-451S
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X51_20141204-1.2.eight.img

TS-x53 Series
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X53_20140916-1.two.8.img

TS-x53U Series
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X53U_20141125-i.2.8.img

TS-453mini
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X53_20150206-1.3.0.img

TS-x53S Series

http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X53S_20150106-1.ii.8.img


========================================================


B. How to use USB boot disk to refresh the DOM for x86 based NAS


1. Ability off the NAS.
2. Remove all the hard disks.

RTENOTITLE

3. Connect the NAS with a VGA/HDMI monitor, USB keyboard, and the bootable USB deejay.


RTENOTITLE

4. Ability on the NAS and press F11 key repeatedly.


RTENOTITLE

v. Select the USB flash drive as your boot device. If you lot didn’t the carte du jour and the system continues to process with the command line mode, please reboot the NAS and repeat the step 4.
[NOTE]: If in that location are ii USB devices, don’t select “USB Disk MODULE PMAP”.

RTENOTITLE

6. On the following menu, select Default for monitor setting. And so, press <Space> to continue.

RTENOTITLE

7. After kicking up completely, y’all should meet the following window.


RTENOTITLE

8. Press Ctrl+Alt+Del to enter command line.
9. Input the post-obit control:
# sudo su
# fdisk –fifty

/dev/sda is your wink drive.
/dev/sdb or /dev/hda is the DOM drive. The size should be 128 MB or 512 MB depend on the NAS model.

RTENOTITLE

10. Then, input the following control:
# mkdir usbdrive
# mountain /dev/sda1 /home/dsl/usbdrive
# cd /habitation/dsl/usbdrive

eleven. Input the following command:
# cp dom.img /dev/sdb

“/dev/sdb” or “/dev/hda” is the DOM drive.

“dom.img” is your firmware name.
/dev/sdb or /dev/hda is the drive name of your dom. (depend on NAS model)

12. Reboot your NAS.
# reboot

RTENOTITLE

13. After the system has been recovered, the NAS should boot up correctly and can be found by QNAP Finder.

fourteen.
When the firmware version is on 1.x.ten, information technology is factory test firmware. No HDD can be detected with this firmware.  Need to update the firmware to official firmware kickoff.

      For TS-239, TS-439, TS-439U, TS-509, TS-639, TS-809, TS-809U, SS-439 and SS-839, please follow the procedures on the following link to update the firmware to 3.5.0.

http://wiki.qnap.com/wiki/NAS_Firmware_Update_When_No_HDD(s)_Installed

      For other x-86 based NAS, please download the firmware iii.4.x from QNAP website and use QNAP Finder to update the firmware.

16. Subsequently firmware update by QNAP Finder, you tin can then plug the HDD(s) dorsum to the NAS.  Later on boot up,

  •       If the HDD(south) have been used on the NAS before, the firmware on the NAS and the HDDs may be inconsistent, you need to update the firmware over again.
  •       If the HDD(s) is brand new, y’all tin can then start the initialization procedures.



Firmware Recovery Guide for TS-453Bmini, TS-269 Pro, TS-269L, TS-x79, TS-x70, TS-x80, TS-ECx80U, SS-ECx79U Serial NAS


Applied QNAP NAS models

TS-453Bmini, TS-269 Pro, TS-269L, TS-879 Pro, TS-879U-RP, TS-1079 Pro, TS-1279U-RP, TS-EC879U-RP, TS-EC1279U-RP, TS-470, TS-470U-RP/SP, TS-670 Pro, TS-870 Pro, TS-870U-RP, TS-1270U-RP, TS-1679U-RP, TS-EC1679U-RP, TS-x80 Pro Series, TS-EXx80U, SS-ECx79U Series


When to employ the firmware recovery guide


This firmware recovery guide is intended for users who encounter arrangement startup failure due to incomplete or unsuccessful firmware update caused by ability outage or network disconnection during the procedure. To verify if this guide applies to your NAS, follow the steps below:

1. Ability off the NAS.
two. Remove all the hard disks.


RTENOTITLE


3. Connect the NAS with a VGA/HDMI monitor and a USB keyboard.


RTENOTITLE


4. Power on the NAS

The BIOS Date and Version should exist displayed. This shows the BIOS can startup correctly

RTENOTITLE

If the BIOS cannot be started, you need to contact with local benefactor and

send dorsum the NAS for repair
. If the NAS organization can exist started up correctly after removing HDD, y’all will

need to replace the HDD

equally the startup failed issue is caused by HDD.

five. Afterward the BIOS info, you will see status letters similar to below:


RTENOTITLE

At this stage, the system on the DOM is starting to boot up. Notwithstanding, if the system is corrupted, some error message might occur on the screen during the startup process. You can endeavour to

recover the organization on the DOM past following steps
.

6. To recover the arrangement on the DOM, you demand follow the pace A and step B.

    A. Create a USB kicking deejay
B. Use the USB boot disk to refresh the arrangement on the DOM.

Instructions for NAS Recovery


A. How to create a USB boot disk.


i. Download the unetbootin utility and iso file from the link below:
http://unetbootin.sourceforge.internet/
– e.g. please select “Download for windows” if you are using Windows platform on your PC.
http://eu1.qnap.com/Storage/tsd/clonezilla-alive-one.ii.11-23-i486.iso

2. Plug a USB flash drive to your PC. The USB flash drive should be 1GB or 2GB. Please format the USB flash drive equally FAT32.

RTENOTITLE

three. Run the unetbootin utility on your PC. Then select “CloneZilla” for Distribution.
4. Select “Diskimage”, and cull the iso file downloaded in step 1.
5. Make certain the Type is on “USB Bulldoze”, and click “OK” to install the boot system on the USB bulldoze.
RTENOTITLE

6. Click “Get out” afterwards process completed.
vii. Check your NAS model and download the system full image from the link below.
8. Copy organisation image file to the root folder of USB flash bulldoze and rename the file to “dom.img”.

Download System Full Image

========================================================

TS-453Bmini
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X53B_20161116-one.3.0.img


TS-879U-RP, TS-EC879U-RP
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-879U_20140515-1.2.viii.img


TS-1079 Pro
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-1079_20140516-1.2.8.img


TS-1279U-RP, TS-EC1279U-RP, TS-EC1279U-SAS-RP
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-1279U_20140516-1.2.8.img

TS-1679U-RP, TS-EC1679U-RP, TS-EC1679U-SAS-RP
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-1679U_20140516-1.2.viii.img

TS-470 / TS-470 Pro
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-470_20140519-ane.two.8.img

TS-470U-RP/SP
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-470U_20140520-ane.2.8.img

TS-670 Pro
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-670_20140520-1.two.8.img

TS-870 Pro
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-870_20140519-1.2.8.img

TS-870U-RP
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-870U_20140520-1.2.8.img

TS-1270U-RP
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-1270U_20140520-1.2.8.img

TS-x80 Pro Series (Belfry)
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X80_20140911-1.2.8.img

TS-x80U Series (Rackmount)
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X80U_20140911-ane.2.8.img

SS-EC1279U
http://eu1.qnap.com/Storage/tsd/fullimage/F_SS-1279U_20130820-1.2.7.img

SS-EC1879U
http://eu1.qnap.com/Storage/tsd/fullimage/F_SS-1879U_20130820-i.2.7.img

SS-EC2479U
http://eu1.qnap.com/Storage/tsd/fullimage/F_SS-2479U_20130820-1.ii.vii.img

========================================================


B. How to utilize USB kicking deejay to refresh the DOM for TS-x79, TS-x70U, TS-x80 series NAS


one. Ability off the NAS.
2. Remove all the difficult disks.

RTENOTITLE

3. Connect the NAS with a VGA/HDMI monitor, USB keyboard, and the bootable USB disk.

Read:  Xt907 Luge Stock Firmware Without Data Wipe


RTENOTITLE

iv. Power on the NAS and press the or <F2> central when you encounter the message to enter setup.


RTENOTITLE

5. You lot will enter the BIOS Setup. Printing the correct arrow key to navigate to the Kicking settings screen, and select “Hard Bulldoze BBS Priorities”


RTENOTITLE

vi. Select “Boot Option #1”

RTENOTITLE


7. Select “Generic USB Flash Disk” or similar name showing your USB disk
[NOTE]: If there are two USB devices, don’t select “USB DISK MODULE PMAP”.

RTENOTITLE

8. Press <F4> and select “Yes” to save and exit.


RTENOTITLE

9. The CloneZilla loader will start up. Press <Enter>.


RTENOTITLE


x. When asked to “Cull Language” and “Configuring Console-data”, press <Enter>

11. At the “Start Clonezilla” option, select “Enter_shell”. Press <Enter> twice.


RTENOTITLE

12. Yous will see the Linux control line. Enter the post-obit commands:
# sudo su
# fdisk –fifty

/dev/sda is your flash bulldoze.
/dev/sdb is the DOM drive. The size should be 515 MB.

RTENOTITLE

13. Then, input the following commands:
# cd /alive/image
# cp dom.img /dev/sdb

“dom.img” is your firmware name.
/dev/sdb is the bulldoze name of the DOM.

14. Reboot your NAS.
# reboot


RTENOTITLE

15. After the system has been recovered, the NAS should boot up correctly and can exist constitute by QNAP Finder.

16. Please download the latest firmware from the QNAP website and use QNAP Finder to update the firmware to latest version.

17. After firmware update past QNAP Finder, you can then plug the HDD(s) back to the NAS. After boot up:

  •       If the HDD(s) have been used on the NAS earlier, the firmware on the NAS and the HDDs may exist inconsistent, you demand to update the firmware once again.
  •       If the HDD(southward) is brand new, y’all can then start the initialization procedures.



Firmware Recovery Guide for TS-251B, TS-x51D series, TS-x53B Serial, TS-x53BU Series, TS-x51A Serial, TS-x53U series, TS-x53A Series, TBS-453A, TBS-453DX, HS-453DX, TS-x53D serial, TVS-x63 Series, TVS-x63+ Series, TVS-x71 Serial, TVS-x71U Series, TVS-x72N Series, TVS-x72X Series, TVS-x72XT Series, TVS-x72XU Serial, TVS-x73 Series, TVS-675, TS-x73U Series, TS-x77 Serial, TS-x77XU Series, TS-hx77XU Series,TS-1685, TVS-ECx80 / TVS-ECx80+, TVS-ECx80U Serial, TVS-x82 Series, TVS-x82T Series, TVS-x82ST Series, TVS-882BR, TVS-882BRT3, TVS-951X, TVS-1282T3, TVS-1582TU, TS-x83XU Series, TS-h1283XU, TDS-16489U, TDS-16489U R2, TES-x85U series, TS-hx88X serial, TS-h3088XU NAS


Practical QNAP NAS models

TS-251B, TS-251D, TS-451D, TS-253B, TS-453B, TS-653B, TS-253Be, TS-453Be, TS-453BT3, TS-453BU, TS-853BU, TS-1253BU, TS-453U, TS-853U, TS-1253U, TS-251A, TS-451A, TBS-453A, TBS-453DX, HS-453DX, TS-253D, TS-453D, TS-653D, TS-253A, TS-453A, TS-653A, TS-853A, TVS-463, TVS-663, TVS-863, TVS-471, TVS-671, TVS-871, TVS-871T, TVS-471U, TVS-871U, TVS-1271U, TVS-672N, TVS-872N, TVS-672X, TVS-872X, TVS-472XT, TVS-672XT, TVS-872XT, TVS-872XU, TVS-972XU, TVS-1272XU, TVS-1672XU, TVS-473, TVS-673, TVS-873, TVS-675, TS-873U, TS-1273U, TS-1673U, TS-677, TS-877, TS-1277, TS-877XU, TS-977XU, TS-1277XU, TS-1677XU, TS-2477XU, TS-h977XU, TS-h1277XU, TS-1685, TVS-ECx80 / TVS-ECx80+ series, TVS-ECx80U Series, TVS-682, TVS-882, TVS-1282, TVS-682T, TVS-882T, TVS-1282T, TVS-882ST2, TVS-882ST3, TVS-882BR, TVS-882BRT3, TVS-951X, TVS-1282T3, TVS-1582TU, TS-883XU, TS-983XU, TS-1283XU, TS-1683XU, TS-2483XU, TS-h1283XU, TDS-16489U, TDS-16489U R2, TES-1885U, TES-3085U, TS-h1288X, TS-h1688X, TS-h3088XU


When to employ the firmware recovery guide

This firmware recovery guide is intended for users who meet system startup failure due to incomplete or unsuccessful firmware update caused by power outage or network disconnection during the procedure. To verify if this guide applies to your NAS, follow the steps beneath:

one. Ability off the NAS.
2. Remove all the hard disks.

RTENOTITLE

3a. Connect the NAS with a VGA/HDMI monitor and a USB keyboard

RTENOTITLE

RTENOTITLE

3b. For some NAS models, there is no VGA or HDMI port but in that location is a panel port on the NAS, similar TS-X77 series, TS-1685,…etc.


RTENOTITLE

RTENOTITLE

    Please prepare console cablevision listed beneath and connect it betwixt NAS panel port and your PC.
Console cable:
D-SUB 9P female to three.5mm stereo plug cable

RTENOTITLE

    Console cable drawing and pin assignment:


RTENOTITLE


You may too need below USB-to-RS232 cable if there is no RS-232 serial port on your PC.

RTENOTITLE

    ( If y’all are not able to go these cable(s) or don’t know how to do it, please apply the RMA to return your NAS for maintenance. )

    Adjacent, you tin cheque which COM port to be used in Windows Device Managing director.
(Hither, COM4 is used for connection.)

RTENOTITLE

    And so you tin can use the terminal utility, (ex: Putty) to connect to the console.
(Baud charge per unit: 115200 bps)

RTENOTITLE

four. Power on the NAS

The BIOS Date and Version should be displayed. This shows the BIOS can startup correctly.

RTENOTITLE

If the BIOS cannot exist started, you demand to contact with local benefactor andship back the NAS for repair. If the NAS system tin can be started upwardly correctly later on removing HDD, you willneed to replace the HDD as the startup failed issue is caused by HDD.

5. After the BIOS info, y’all will run into condition letters like to below:

RTENOTITLE

At this stage, the system on the DOM is starting to kick upward. Nonetheless, if the organisation is corrupted, some error message might occur on the screen during the startup procedure.
You lot tin can try torecover the system on the DOM by following steps.

half dozen. To recover the organisation on the DOM, y’all need follow the step A and stride B.

    A. Create a USB kicking disk
B. Utilize the USB boot disk to refresh the system on the DOM.



Instructions for NAS Recovery

A. How to create a USB boot deejay.

(for TS-hx88X Series / TS-h3088XU NAS, delight download beneath version of clonezilla.)
https://osdn.cyberspace/projects/clonezilla/downloads/74519/clonezilla-alive-2.7.1-22-amd64.nothing/

2. Plug a USB flash bulldoze to your PC. Please format the USB wink drive as FAT32.

RTENOTITLE

three. Run the rufus utility from your PC and click it to select
– “clonezilla-live-ii.five.0-25-amd64.iso” as your ISO file. (for HS-453DX, TS-251D/TS-451D/TS-253D/TS-453D/TS-653D/TS-251B/TS-253B/TS-453B/TS-653B/TS-253Be/TS-453Be/TS-453BT3/TVS-675/TS-677/TS-877/TVS-951X/TS-1277 only)
– “clonezilla-alive-two.5.0-25-amd64_console.iso” as your ISO file. (for TS-x77 Series/TS-x77XU Series/TS-h977XU/TS-h1277XU/TS-x83XU Serial/TS-h1283XU/TS-1685/TES-1885U/TES-3085U only)
– “clonezilla-live-2.7.1-22-amd64.iso” every bit your ISO file. (for TS-h1288X / TS-h1688X / TS-h3088XU only)
– “clonezilla-alive-2.4.2-ten-amd64.iso” as your ISO file. (for other models)

RTENOTITLE

4. Click Start button to starting time preparing the USB flash drive.

five. Bank check your NAS model and download the arrangement full image from the link below.

6. Copy arrangement image file to the root folder of USB flash drive and rename the file to “dom.img”.

Download Organisation Full Image

==============================================================================================
TS-1685
http://download.qnap.com/Storage/tsd/fullimage/F_TS-X85_20170210-1.3.0_512M.img

TS-677 / TS-877 / TS-1277
http://download.qnap.com/Storage/tsd/fullimage/F_TS-X77_20170908-i.three.0_4G.img

TS-877XU / TS-977XU / TS-1277XU / TS-1677XU / TS-2477XU
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X77U_20181001-1.3.0.img

TS-h977XU / TS-h1277XU
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X77U_20200507-1.3.0.img

TS-251B
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X51B_20180417-i.3.0.img

TS-251D / TS-451D

https://download.qnap.com/Storage/tsd/fullimage/F_TS-X53D_20190919-one.3.0.img

TS-253B / TS-453B / TS-653B / TS-253Be / TS-453Be / TS-453BT3
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X53B_20161212-i.3.0_EFI.img

TS-453BU / TS-853BU / TS-1253BU
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X53BU_20180606-i.3.0.img

TS-453U / TS-853U / TS-1253U
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X53U_20141125-1.ii.viii.img

TS-251A / TS-451A
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X51A_20160429-1.three.0_EFI.img

TBS-453A
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X53A_20160531-1.3.0_EFI.img

TBS-453DX / HS-453DX
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X53D_20180510-1.3.0.img

TS-253D / TS-453D / TS-653D
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X53D_20210303-1.3.0.img

TS-253A / TS-453A / TS-653A / TS-853A
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X53II_20151028-1.3.0_TDS-special.img

TVS-471 / TVS-671 / TVS-871
http://eu1.qnap.com/Storage/tsd/fullimage/F_TVS-X71_20141126-1.2.eight.img

TVS-871T
http://eu1.qnap.com/Storage/tsd/fullimage/F_TVS-X71_20150611-1.3.0.img

TVS-471U / TVS-871U
http://eu1.qnap.com/Storage/tsd/fullimage/F_TVS-X71U_20141126-ane.2.8.img

TVS-1271U
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X71U_20140925-1.two.8.img

TVS-463 / TVS-663 / TVS-863 / TVS-863+
http://eu1.qnap.com/Storage/tsd/fullimage/F_TVS-X63_20141224-1.two.8.img

TVS-472XT / TVS-672XT / TVS-872XT
http://download.qnap.com/Storage/tsd/fullimage/F_TS-X72_20190122-1.3.0.img

TVS-672N / TVS-872N / TVS-672X / TVS-872X

https://download.qnap.com/Storage/tsd/fullimage/F_TS-X72_20201210-1.3.0.img

TVS-675

https://download.qnap.com/Storage/tsd/fullimage/F_TS-X75_20210414-h1.3.0_UEFI.img

TVS-872XU / TVS-972XU / TVS-1272XU / TVS-1672XU
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X72U_20180824-1.3.0.img

TVS-473 / TVS-673 / TVS-873
http://eu1.qnap.com/Storage/tsd/fullimage/F_TVS-X73_20160908-1.three.0.img

TVS-473e / TVS-673e / TVS-873e
https://download.qnap.com/Storage/tsd/fullimage/F_TVS-X73_20171208-1.3.0.img

TS-873U / TS-1273U / TS-1673U
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X73U_20170526-1.3.0.img

TVS-ECx80 / TVS-ECx80+ Series
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X80_20140930-1.2.eight.img

TVS-ECx80U Serial
http://eu1.qnap.com/Storage/tsd/fullimage/F_TVS-X80U_20150818-i.iii.0.img

TVS-682 / TVS-882 / TVS-1282
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X82_20160520-1.3.0.img

TVS-682T / TVS-882T / TVS-1282T
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X82_20160824-i.3.0.img

TVS-882ST2 / TVS-882ST3
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X82S_20170606-1.3.0.img

TVS-882BR / TVS-882BRT3
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X82_20170512-ane.3.0.img

TVS-951X
https://download.qnap.com/Storage/tsd/fullimage/F_TS-XA82_20180329-1.3.0.img

TVS-1282T3
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X82_20170606-1.3.0.img

TS-883XU / TS-983XU / TS-1283XU-RP / TS-1683XU-RP / TS-2483XU-RP
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X83XU_20181012-1.3.0.img

TS-h1283XU-RP
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X83XU_20200416-1.3.0.img

TVS-1582TU
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X82U_20170314-1.iii.0.img

TDS-16489U (QTS)
http://eu1.qnap.com/Storage/tsd/fullimage/F_TS-X89U_20160408-i.3.0.img

TES-1885U / TES-3085U
http://download.qnap.com/Storage/tsd/fullimage/C_TESX85U_20190430.usb

TS-h1288X / TS-h1688X
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X88_20210109-h1.3.0_UEFI.img

TS-h3088XU
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X88U_20201217-h1.3.0_UEFI.img

========================================================

B. How to utilize USB boot deejay to refresh the DOM for NAS

1. Ability off the NAS.
2. Remove all the hard disks.
iii. Connect the NAS with a USB wink drive and
– VGA/HDMI monitor and a USB keyboard (if in that location is VGA or HDMI port on the NAS)
– Console cable (if there is only panel port on the NAS)
4. Power on the NAS and pressDEL
key when yous run across the message to enter BIOS settings.

RTENOTITLE


5. Printing right pointer key to navigate to the Boot choice and select your USB flash bulldoze, similar Patriot Memory.
(Do non select USB DISK MODULE because it is USB DOM in the system.)

RTENOTITLE

5a. Since some of new NAS model (similar HS-453DX, TVS-951X, TS-h1288X, TS-h1688X, TS-h3088XU) is with UEFI BIOS, delight choose select your USB flash bulldoze at UEFI. Ex: [ UEFI: Patriot Memory ]
RTENOTITLE

6. Salvage settings and get out BIOS.

RTENOTITLE

7. It volition kicking up with your USB flash drive.
7a. For NAS with console port but (like TS-677,TS-877,TS-1277,TS-1685,TES-1885U,TES-3085U,…etc.), select Clonezilla Alive (Serial console) pick.

RTENOTITLE

   7b. For other NAS with VGA or HDMI port, select Clonezilla Live pick.

RTENOTITLE



RTENOTITLE



RTENOTITLE

8. Follow below steps to enter the beat out console.

RTENOTITLE



RTENOTITLE

9. Y’all will see the Linux command line. Enter the following commands:
[~]# sudo su
[~]# fdisk –l

/dev/sda is your flash drive.
/dev/sdb is the DOM drive. The capacity is 492 MB.

RTENOTITLE

For TDS-16489U R2 / TES-1885U / TES-3085U, /dev/sdb is the DOM bulldoze. The chapters is three.9GB.

RTENOTITLE

For TS-h1288X/TS-h1688X/TS-h3088XU, /dev/sdb is the DOM drive. The capacity is iv.64 GB.

RTENOTITLE

Read:  Dji Phantom 3 How to Turn Off Firmware Auto Updates?

For TVS-675, /dev/sdb is the DOM bulldoze. The capacity is 4.7 GB.

(For TS-251A/TS-451A/TBS-453A/TBS-453DX/HS-453DX, “/dev/mmcblk0” is your DOM drive)
(For TS-251B/TS-253B/TS-453B/TS-653B/TS-253Be/TS-453Be, “/dev/mmcblk1” is your DOM drive)


RTENOTITLE

ten. Execute below commands:
[~]# cd /lib/live/mount/medium/

(For TS-251A/TS-451A/TBS-453A/TBS-453DX/HS-453DX, delight execute below command)
[~]# cp dom.img /dev/mmcblk0

(For TS-251B/TS-253B/TS-453B/TS-653B/TS-253Be/TS-453Be/TS-453BT3, please execute beneath command)
[~]# cp dom.img /dev/mmcblk1

(For TS-h1288X / TS-h1688X / TS-h3088XU, delight execute below command)
[~]# cp dom.img /dev/sda

(For other models, please execute beneath command)
[~]# cp dom.img /dev/sdb

11. Subsequently the copy is completed, reboot the organisation.
[~]# reboot

12. Remove the USB flash drive from the organization.

13. Afterward the arrangement has been recovered, the NAS should boot up correctly and can be found past QNAP Finder. (Note: Non completed yet.)

14. Please download the latest firmware from the QNAP website and employ QNAP Finder to update the firmware to latest version.
(Note: Brand sure you have done this step after the system recovery.)

xv. Later on firmware update by QNAP Finder, you can then plug the HDD(s) back to the NAS.
After boot upwardly:

  • If the HDD(s) have been used on the NAS before, the firmware on the NAS and the HDDs may be inconsistent, you need to update the firmware again.
  • If the HDD(s) is brand new, you can then start the initialization procedures.



Firmware Recovery Guide for AL (Annapurna Labs) based NAS


Practical QNAP NAS models

For QNAP TS-131P, TS-231P, TS-431P, TS-231P2, TS-231K, TS-431K, TS-431P2, TS-231+, TS-431+, TS-431X, TS-431X2, TS-531P, TS-531X, TS-831X, TS-832X, TS-932X, TS-431XU, TS-431XeU, TS-831XU, TS-1231XU, TS-1635, ,TS-832XU, TS-1232XU Turbo NAS.


When to use the firmware recovery guide

This firmware recovery guide is intended for users who encounter organization startup failure due to incomplete or unsuccessful firmware update caused by power outage or network disconnection during the process.


Instructions for NAS Recovery


Prepare a Windows PC and configure the network port as a static IP: 169.254.100.177.

  1. Download and install tftp server software to the Windows PC.
    For 32-bit Windows:http://tftpd32.jounin.net/download/tftpd32.452.goose egg

    For 64-scrap Windows:
    http://tftpd32.jounin.net/download/tftpd64.452.nothing
  2. Download firmware files:
    TS-832X/TS-932X:http://download.qnap.com/Storage/tsd/fullimage/TS-X32X.cipher

    TS-832XU/TS-1232XU:http://download.qnap.com/Storage/tsd/fullimage/TS-X32XU_fw.zip

    TS-231K/TS-431K:https://download.qnap.com/Storage/tsd/fullimage/TS-X31K_fw.zip

    (If your NAS QTS firmware version is

    before than v4.iii.4
    , please click below link to download.)
    TS-431X/TS-531X/TS-831X/TS-431X2:
    http://download.qnap.com/Storage/tsd/fullimage/TS-X31X_fw.zip

    TS-431XU/TS-431XeU/TS-831XU/TS-1231XU:
    http://download.qnap.com/Storage/tsd/fullimage/TS-X31XU_fw.zilch

    TS-531P:
    http://download.qnap.com/Storage/tsd/fullimage/TS-531P_fw.cipher

    TS-131P/231P/431P/X31+:
    http://download.qnap.com/Storage/tsd/fullimage/TS-X31P+_fw.nothing

    TS-231P2/TS-431P2:
    http://download.qnap.com/Storage/tsd/fullimage/TS-X31P2.zip

    TS-1635:http://download.qnap.com/Storage/tsd/fullimage/TS-1635_fw.zip

    (If your NAS QTS firmware version is

    equal or later than v4.3.iv
    , delight click below link to download.)
    TS-431X/TS-531X/TS-831X/TS-431X2:
    http://download.qnap.com/Storage/tsd/fullimage/TS-X31X_434.zip

    TS-431XU/TS-431XeU/TS-831XU/TS-1231XU:
    http://download.qnap.com/Storage/tsd/fullimage/TS-X31XU_434.zip

    TS-531P:
    http://download.qnap.com/Storage/tsd/fullimage/TS-531P_434.zippo

    TS-131P/231P/431P/X31+:
    http://download.qnap.com/Storage/tsd/fullimage/TS-X31P+_434.zip

    TS-231P2/TS-431P2:
    http://download.qnap.com/Storage/tsd/fullimage/TS-X31P2_434.zip

    TS-1635:http://download.qnap.com/Storage/tsd/fullimage/TS-X35_434.zip

  3. Launch tftp server application on the PC and configure the server settings similar below.

    Tftp Server Settings

  4. Current Directory: Specify the directory where the firmware files are stored.
    Server interfaces: Specify the network port on your PC which you lot configured IP address as 169.254.100.177.
  5. Power off the NAS.
  6. Remove all of hard disks from the NAS.
  7. Connect the network cable to the specific network port of NAS.
    (Attention: Please refer to below NAS photos to connect to correct port marked in blueish.)

    RTENOTITLE

    RTENOTITLE



    RTENOTITLE

    TS-1635_review



    RTENOTITLE



    RTENOTITLE
  8. Press and hold USB copy button and and so press ability push button to power on the NAS. Wait about 6 seconds until the condition LED turns Reddish. Then release USB copy push.
    (PS: TS-531P is the exception that the condition LED will not plow red.)
  9. For the model, TS-431XU/TS-831XU/TS-1231XU/TS-832XU/TS-1232XU, which does not have USB copy button, please practice beneath steps instead.
    – Open up the enclosure case.
    – Find J2 pin shown in below effigy.
    – Connect a jumper on it.
    – Ability on the NAS.

    TS-X31XU Jumper.jpg

  10. The firmware recovery will automatically start and you can run into firmware files downloaded from tftp server to NAS. (Come across below screenshot.)

    RTENOTITLE
  11. Once the firmware recovery process is done, the NAS will shutdown automatically.
    (PS: TS-531P is the exception that the NAS will reboot instead of shutdown.)
  12. Remove the jumper from pin J2 (for TS-431XU/TS-831XU/TS-1231XU/TS-832XU/TS-1232XU only).
  13. Done.



USB Firmware Recovery SOP for TS-328, TS-X28A Series and TS-X30 serial NAS


Applied QNAP NAS models

For TS-128A, TS-228A, TS-328 NAS, TS-130, TS-230


When to use the firmware recovery guide

This firmware recovery guide is intended for users who encounter system startup failure due to incomplete or unsuccessful firmware update acquired by power outage or network disconnection during the procedure.


Instructions for NAS Recovery


A. How to create a USB kick disk.


1. Download the rufus utility into your PC from the link beneath.:
https://github.com/pbatard/rufus/releases/download/v3.4/rufus-iii.4.exe

two. Download the NAS system prototype into your PC from the link below.
TS-128A / TS-228A
http://download.qnap.com/Storage/tsd/fullimage/F_TS-X28A_20171219-i.3.0.img

TS-328
http://download.qnap.com/Storage/tsd/fullimage/F_TS-XA28A_20180329-1.3.0.img

TS-130 / TS-230
https://download.qnap.com/Storage/tsd/fullimage/F_TS-XA28A_20190917-ane.3.0.img

three. Plug in USB disk into your PC.
four. Run the rufus utility from your PC and click the button to select the system prototype file.

RTENOTITLE

5. Click “Start” button to write the organization image into USB disk.

B. How to use USB boot disk to refresh the DOM for NAS.


1. Ability off the NAS.
2. Uninstall all of the disk drives from the NAS.
3. Connect the USB flash bulldoze to rear USB port of the NAS.

RTENOTITLE

RTENOTITLE

RTENOTITLE


4. Press and concord the USB re-create push and and then press Ability push to power on the NAS.
five. Keep belongings the USB copy push till you hear a beep sound and then release it.

RTENOTITLE


6. Once you lot hear 3 short beeps, information technology ways the firmware recovery is existence started. If not, delight ability off the NAS and redo information technology with the above steps 4 to 6.
7. After the firmware recovery is done, you will hear a long beep and and then NAS will be shut down automatically. (Note: If y’all hear ii long beeps or the NAS is not shutdown after 5 minutes, the firmware recovery might fail. Please redo the process again.)
8. Remove the USB wink drive from the NAS and power on the NAS.
ix. The NAS should boot up correctly and tin be found by QNAP Finder. (Note: Not completed yet.)
10. Please download the latest firmware from the QNAP website and use QNAP Finder to update the firmware to latest version.(Note: Make certain you have done this step after the arrangement recovery.)

RTENOTITLE


12. Shutdown NAS and plug all HDD(s) dorsum to NAS and power on NAS.
13. Done.


USB Firmware Recovery SOP for TS-435XeU series NAS


Applied QNAP NAS models

For TS-435XeU


When to use the firmware recovery guide

This firmware recovery guide is intended for users who meet organisation startup failure due to incomplete or unsuccessful firmware update caused by power outage or network disconnection during the process.


Instructions for NAS Recovery


A. How to create a EXT4 USB drive.


1. You lot need to prepare a USB bulldoze and format it to EXT4 format
Download the AOMEI Partition Assistant into your PC from the link below.:
https://www.diskpart.com/download-home.html#demo

2. Download the NAS system image into your PC from the link below.
TS-435XeU
https://download.qnap.com/Storage/tsd/fullimage/F_TS-X35EU_20220119-1.3.0_UEFI.img

three. Plugin a USB bulldoze into your PC.

iv. Install the AOMEI Sectionalisation Assistant from your PC and format the USB drive to EXT4 format

5. Use Ubuntu(Linux) to re-create NAS’south image files into EXT4 USB drive.

6. Rename the image name to emmc_recovery_fi.img (Make sure it save in USB drive partitioning one)

B. How to employ USB boot drive to refresh the DOM for NAS.


ane. Power off the NAS and unplug the ability cord.

2. Remove the 5 screws with a screwdriver and unlock&open up the NAS’s case.

3. Find a pin most “USB COPY” text, plugin a jumper to that pin every bit below.(jumper is in blue color)

        
          RTENOTITLE
        
        

iv. Plugin the EXT4 USB drive to USB port(whatever of 4 USB ports are ok).

five. Brand sure no network cables plugin and no any HDD(s) plugin, merely plugin the EXT4 USB drive and jumper.

6. Plugin the power cord to power on the NAS.

vii. Front LED volition accept blink red(Information technology’s refresh DOM now).

viii. Look for it finished, will shutdown the NAS automatically.

9. Unplug the jumper.

10. Unplug the EXT4 USB bulldoze from USB port.

eleven. Poewr on the NAS and have a PC connect to NAS directly via network port.

12. Download the latest firmware from the QNAP website and employ QNAP QFinder Pro to update the firmware to latest version.(Annotation: Brand sure you lot have done this footstep afterwards the organisation recovery.)

12. Shutdown NAS and plug all HDD(s) back to NAS and power on NAS.

xiii. Done.


What to do if the startup problem persists

If the startup problem persists after refresh the organisation on the DOM, please render the NAS to your local dealer or distributor for system repair immediately.



Qnap Nas 4.3.4 Not Show Firmware Update

Check Also

Rolling Back Dji Mavic Firmware on Mac

Rolling Back Dji Mavic Firmware on Mac

Rolling Back Dji Mavic Firmware on Mac DJI introduces new firmware to fix bugs and …