Printer Hp Officejet Pro 8710 All in One

Printer Hp Officejet Pro 8710 All in One

Z7_3054ICK0KGTE30AQO5O3KA30N0



hp-concentra-wrapper-portlet





Actions

HP OfficeJet 8600 Printers – First Time Printer Setup

This document is for the following printers:

HP OfficeJet 8600 Series Printer

HP Officejet Pro 8610 e-All-in-Ane Printer

HP Officejet Pro 8625 e-All-in-1 Printer

HP Officejet Pro 8600 e-All-in-One Printer

HP Officejet Pro 8615 eastward-All-in-One Printer

HP Officejet Pro 8630 east-All-in-Ane Printer

HP Officejet Pro 8600 Plus eastward-All-in-One Printer

HP Officejet Pro 8616 e-All-in-One Printer

HP Officejet Pro 8640 e-All-in-1 Printer

HP Officejet Pro 8600 Premium e-All-in-I

HP Officejet Pro 8620 e-All-in-One Printer

HP Officejet Pro 8660 e-All-in-One Printer

To ready up a printer for the starting time fourth dimension, remove the printer and all packing materials from the box, connect the power cable, gear up command console preferences, load paper into the input tray, install the ink cartridges, and then download and install the printer software.

Step 1: Remove the printer from the box

Remove the printer from the box and all record, stickers, and packing materials from the printer.

The contents might vary past country/region. Run across the packaging for a list of items shipped in the box.

  1. Remove the printer from the box.

  2. Remove all record and packing materials from the outside of the printer.

    Figure
    : Remove the packing materials


    Image: Remove the tape and packing materials

  3. Remove the sticker on the control panel brandish.

  4. Place your fingers into the slot on the left side of the printer, and then pull to open up the ink cartridge access door.

    Figure
    : Slot on the left side of the printer


    Image: Slot on the left side of the printer

  5. Remove all record and packing materials from inside the printer.

  6. Shut the ink cartridge access door.

  7. Recycle the packing materials.

Stride ii: Install the two-sided printing accessory (duplexer)

Afterwards the printer is unpacked, install the duplexer.

  1. Find the duplexer in the box.

  2. Take the duplexer out of its packing material, and then remove any tape from the duplexer.

  3. Turn the printer so the rear faces you lot.

  4. Hold the duplexer past its sides with the rollers toward the printer, insert it into the slot in the rear of the printer, and and then push the duplexer into the printer until it snaps into place.

    note:

    Wait for the engraved arrows on the duplexer for help positioning it.

    Effigy
    : Insert the duplexer


    Image: Insert the duplexer into the rear access area

  5. Plough the printer dorsum around so the forepart faces yous

Pace 3: Install Tray 2 (optional)

Tray 2 is an optional accompaniment. If your printer does non include a Tray 2, continue to the next step.

  1. Remove Tray 2 from its box, remove its packing material, and so remove any tape from the tray.

  2. Identify the tray on a flat, level surface where you intend to utilise the printer.

  3. Lift the printer, position it over the top of the newspaper tray, and then lower the printer on height of the paper tray.



    caution:

    Go along your fingers and hands clear of the bottom of the printer.

    Figure
    : Set the printer on tiptop of Tray 2


    Image: Lower the printer onto Tray 2

  4. Make certain the printer is even with the left, right, and back edges of the tray.

Step four: Connect the power cord and set your preferences

One time yous take installed the duplexer, plug the printer into a power source, plough on the printer, and then set your preferences.

note:

Practise not connect a USB cable now.
If you plan to use a USB cable to connect the printer to the reckoner, the installer prompts you to connect it at the correct fourth dimension during the software installation.

  1. Connect the power cord to the rear of the printer, then plug the other cease of the ability cord into an electrical outlet.

    Effigy
    : Connect the power cord


    Image: Plug the power cord into the printer and the electrical outlet

  2. Plough on the printer.

  3. On the printer control panel, touch your preferred language, and and then bear upon
    Go along
    to confirm your choice.

  4. Swipe your finger up and down the display to select your specific country/region, then touch on
    Continue
    to confirm your choice.

  5. Touch
    Date and Fourth dimension, and and then swipe your finger up and down the display to ready the month, day, and year.

  6. Touch
    Done.

Step 5: Load paper into Tray 1

Load plain U.S. letter or A4 newspaper into Tray 1.

  1. Grasp the underside of Tray i, so pull out the tray.

    Figure
    : Pull out the newspaper tray


    Image: Pull out the paper tray.

  2. Pinch the paper width guide tabs, and so slide the newspaper width guides to their outermost positions.

    Figure
    : Slide out the paper width guides


    Image: Slide out the paper width guides.

  3. Insert plain white newspaper in the tray. Make sure that the print side is face-down and the brusque edge is forward.



    caution:

    Do not fill the paper above the yellow, dotted lines on the sides of the paper tray.

    Figure
    : Load paper into the paper tray


    Image: Load paper into the paper tray.

  4. If necessary, slide the paper width guides inward then that they residual on the edges of the newspaper.

  5. Push the tray toward the printer until it locks into place.

    Figure
    : Push in the paper tray


    Image: Push in the paper tray.

  6. Pull out the output tray extender, and and so raise the paper grab.

    Figure
    : Pull out the tray extender


    Image: Pull out the tray extender.

Pace 6: Load paper into Tray 2 (optional)

If yous accept Tray 2, you tin load paper into the tray. If your printer does not include a Tray ii, continue to the next step.

  1. Grasp the underside of Tray 2, and then pull out the tray.

    Figure
    : Pull out Tray ii


    Image: Pull out Tray 2.

  2. Slide out the paper width guides to their outermost positions.

    Effigy
    : Slide out the newspaper width guides in paper Tray 2


    Image: Slide out the paper width guides in Tray 2.

  3. Insert a stack of plain white paper in the center of the tray. Brand sure that the print side is down.



    caution:

    Do not make full the newspaper higher up the ruby lines on the gauges on the sides of the tray.

  4. Slide in the paper guides then that they rest against the edges of the newspaper.

    Figure
    : Slide in the paper width guides for paper Tray 2


    Image: Slide in the paper width guides for paper Tray 2

  5. Gently reinsert the tray into the printer.

  6. Pull out the output tray extender, and so raise the newspaper grab.

    Effigy
    : Pull out the tray extender


    Image: Pull out the tray extender.

Step 7: Install the SETUP ink cartridges

Install the HP SETUP ink cartridges that came in the box with your printer.



caution:

Yous must install the SETUP ink cartridges when offset setting up the printer, or an ink cartridge fault occurs.

  1. Place your fingers into the slot on the left side of the printer, and then pull to open the ink cartridge access door.

    Figure
    : Place your fingers in the slot on the left side of the printer


    Image: Slot on the left side of the printer

  2. Expect until the printer is idle and silent before y’all continue.

  3. Remove the ink cartridge from its package.

    note:

    After y’all remove an ink cartridge from its packet, install it right abroad to avoid damaging the ink.

  4. Hold the ink cartridge by its sides with the nozzles toward the printer, insert the ink cartridge into its slot, and so button the ink cartridge forrad until information technology snaps into identify.

    Figure
    : Insert the ink cartridge


    Image: Inserting the ink cartridge

  5. Repeat these steps to install all the new ink cartridges.

  6. Close the ink cartridge admission door.

  7. Await for the printer to align the ink cartridges.

    Subsequently the alignment is consummate, the printer prints an alignment page.

    note:

    If your printer is the
    HP Officejet 8640, a message displays to use simply genuine HP ink cartridges. Affect
    Yep
    to accept the terms of use.

Footstep 8: Install the printer software

Your HP printer hardware is now fix and you can install the printing software. Do not attempt to connect the printer to a calculator until instructed to do so in the printing software.

Download the latest version of the printing software from the following HP websites:

note:

Some of the printers in the listing have similar names. Make sure to select the link next to the verbal proper noun of your printer.

Step 9: Prepare the printer for fax

Afterward yous complete the previous setup steps, apply one of the following links to ready the printer to send and receive faxes.

Printer model

Link

HP Officejet 8600 Serial printers

HP Officejet Pro 8610 printers

HP Officejet Pro 8615 printers

HP Officejet Pro 8616 printers

HP Officejet Pro 8620 printers

HP Officejet Pro 8625 printers

HP Officejet Pro 8630 printers

HP Officejet Pro 8640 printers

HP Officejet Pro 8660 printers

HP Officejet Pro 8600 printers

HP Officejet Pro 8600 Plus printers

HP Officejet Premium 8600 Plus printers

Printer Hp Officejet Pro 8710 All in One

Read:  Troubleshooting and Routine Maintenance Brother Printer Dcp J140w

You May Also Like