Netgear Router Go Back to Original Firmware From Ddwrt

Before yous brainstorm you lot will demand to get together these resources:

1. A button pin, condom pin or needle.

2. A copy of the latest WNDR3700 firmware which you can download
[
HERE
]

Note that this guide was written for the Netgear WNDR3700-100NAS Revision: 02R1 using Windows 7 64-fleck. This volition piece of work for any WNDR3700 router currently running DD-WRT.

Pace 1: Setting Your Static IP Address

It is important that you setup a static IP address on your calculator. Navigate to:
“Start” -> “Control Console” -> “Network and Internet” -> “Network and Sharing Centre” -> “Change adapter settings“
(left side). Now right click on your local area connectedness and open up the properties window. Select “
Internet Protocol Version 4 (TCP/IPv4)
” and click on backdrop. Enter the following information then click “OK”.

Step 2: Placing the Router Into Recovery Mode

Kickoff past turning off the router using the ability button on the back of the device. Now, using the small object of your selection, press and agree the “Restore Manufactory Settings”, as well known equally the Reset button located on the bottom of the router (there is a cherry-red ring around it). While holding the rest button, plough the router back on. Continue to hold the reset push for approximately 45 seconds and so release it.

** NOTE:

Before you lot release the reset push, merely exist sure the power LED light on the router is flashing. If information technology isn’t, proceed to hold it for about another 15 seconds until it is flashing.

Step 3: Enable the TFTP Client in Windows

If you are using Windows Vista or Windows 7, yous will need to enable the TFTP client. To practise this, navigate to:
“Start” -> “Control Panel” -> “Programs” -> “Programs and Features” -> “Turn Windows features on or off“
(left side). From at that place, scroll down until you spot “TFTP Client”. Cheque the box if it isnt already and click “OK”. Exit the control panel.

Step 4: Flash the Firmware

Start by opening up a control prompt. From there you volition want to type “cd desktop” in social club to change your working directory to your desktop. Bold of grade that is where you saved the firmware download. Now for the fun fleck. In the control window blazon:

** Notation:

Exist sure to use the advisable name of the file you are trying to wink. It may be a afterwards version so the 1 I used every bit an example.

Stride 5: The Waiting Game

This would exist the perfect fourth dimension to go take hold of a drink or hit the washroom. You need to be patient. Do non turn off, restart, unplug cables or otherwise interact with your router. It may take a picayune while; this is normal! Lookout man the power LED light on the front of the router. It should remain orangish throughout the procedure. One time it is complete, it will plow green. At this point you may proceed to point your browser to “192.168.1.ane” and go on to setup your router.

Skillful luck!

Atheros wireless settings
Hither

WNDR3700
Wiki

OpenVPN configuration I take refined:
OpenVPN Config

ALL WNDR3700 users please make full out this curt
Poll

Since the Linux tftp command appears to utilise different options, here is your method modified for Linux users.

Step one: Setting Your Static IP Address

Information technology is of import that you lot setup a static IP address on your estimator. The following assumes you’re using
Network Manager, but should be similar using other managers.

Right click on the network icon elevation left of your screen, choose “Edit Connections…”

On the
Wired
tab, click on your connection and choose “Edit…”. Select the
IPv4 Settings
tab, modify
Method:
to
Manual, then
Add
an Address: 192.168.1.2, Netmask 255.255.255.0 and go out the remainder blank. Apply, then exit Network Managing director and reconnect.

Step 2: Placing the Router Into Recovery Style

Start by turning off the router using the power button on the back of the device. Now, using the small object of your choice, press and hold the “Restore Factory Settings”, also known equally the Reset push button located on the bottom of the router (there is a red ring around it). While property the rest button, plough the router back on. Keep to hold the reset button for approximately 45 seconds then release it.

** NOTE: Before you release the reset button, only exist sure the power LED light on the router is flashing
Green. If it isn’t, continue to hold it for about another xv seconds until information technology is flashing.

Pace 3: Install tftp if you don’t have it.

If you don’t have information technology installed, install the tftp program using you distribution’s repositories and your method of selection.

Step 4: Flash the Firmware

Open a last, then

(or the directory where the firmware is).

Lauch the tftp program, connecting it to the WNDR3700:

At the prompt, set tftp fashion to binary, and the host to the WNDR3700

Yous can check everything is set fine with the status control,

to which tftp should reply:

Time to transfer the firmware:

You should run across in return:

You can so exit tftp:

and await (see Step 5).

** Notation: Be sure to utilise the advisable name of the file you are trying to wink. It may be a later version and so the one I used equally an example.

** NOTE FOR LINUX USERS: tftp doesn’t seem to accept absolute paths. Only cd in the directory where your firmware is earlier launching tftp.

Step five: The Waiting Game

This would be the perfect fourth dimension to get take hold of a drink or hit the washroom. You need to exist patient. Do not turn off, restart, unplug cables or otherwise interact with your router. It may take a lilliputian while; this is normal! Watch the power LED light on the forepart of the router. It should remain orange throughout the procedure. Once it is consummate, it volition turn green. At this signal you may proceed to point your browser to “192.168.one.1” and continue to setup your router.

Thought I was in trouble afterward loosing connectedness and being unable to fix it on my Alienware laptop and so I thought I would change firmware from Netgear WNDR3700-V1.0.4.68NA to dd-wrt wndr3700-factory_NA just subsequently switching I didn’t like it.

So I tried to switch back to stock Netgear, Uh Oh… I didn’t read alee, LOL. Big fault! Searched for hours trying to figure this out to no avail. Then luckily found this post and finally a way to switch back that actually works!

Merely wanted to say cheers so much for the tutorial, everything worked perfectly and only!

Thanks again,

Daniel

Likewise, if you’re getting those timed out requests, make sure the cablevision is going from your figurer to one of the 4 ethernet ports, and not the internet port on the router.