Mtk Usb Port Driver Windows 10 64 Bit Download
You should upgrade or use an
alternative browser.
Windows 10 MTK VCOM USB Drivers for 32 & 64 chip + Driver install tutorial
To determine the version of Windows 10 that you have (32 bit or 64 bit):
– Correct-click on Start then click on Organisation
– In the Organization window that opens, in System section, you will observe your version of Windows side by side to System blazon
To disable Windows 10 64 scrap driver signature enforcement:
– On your 64 bit Windows x desktop click on Start then on Settings
– Click on Update & security then in the left pane click on Recovery
– Nether Advanced startup click on Restart at present push button
– Click on Troubleshoot then on Avant-garde options
– Click on Startup Settings then on Restart button
– The computer volition restart with the Startup Settings screen
– To disable the driver signature enforcement until next restart press on number key 7 or F7 on your keyboard.
– After restart yous can proceed with the unsigned MTK drivers installation for your 64 bit Windows
– After yous install the unsigned drivers, to apply them over again in the future, you have to repeat this procedure
To install the MTK VCOM USB Drivers on 32 & 64 bit Windows x:
– Download the drivers *.zip archive and extract the folder from inside on to the desktop:
https://www.androidfilehost.com/?fid=24269982087012126
Right-click on
Start
then click on
Device Manager
In the
Device Director Window
click on the first item – your figurer name
Click on
Action
and then Add legacy hardware
On the
Welcome to the Add hardware Wizard
window click on
Next
button
Select
Install the hardware that I manually select from a list (Advanced)
and and so click on
Next
button
Click on
Testify All Devices
so on
Next
push
In the
Add Hardware window
click on
Accept Disk… button
In the
Install From Deejay
windows click on
Browse… push button
In the adjacent window –
Locate file
– browse for the folder that y’all take extracted on the desktop at the beginning
Select the version of the driver according to your Windows 10 version – x64 for
64
bit and x86 for
32
bit and click
Open
button
Click the
OK
button to load the driver
From the
list of drivers select MTK USB Port
and click on
Next
button
If a
red warning window
will open,
click
on Install
this commuter software anyway
This action will add the following drivers in to the operating system:
– MediaTek DA USB VCOM Port
– MediaTek PreLoader USB VCOM Port – for transferring the firmware to your device
– MTK USB DEBUG Port
– MTK USB Modem Port
– MTK USB port – for transfering PreLoader to your device (and recovery in case of bad or decadent firmware)
Now we need to remove the
device
that we have installed only leave the drivers in the operating system.
To practice that, in the
Device Manager window
we expand Ports
(COM & LPT)
section
Right-click and click
Uninstall
on the
MTK USB Port
– In the Confirm Device Uninstall window make sure that the box
Delete the driver software for this device is empty
– You need to get out the drivers in the operating system and only remove the device that you added
– Click on the
OK
push button to finalise
Now, when you volition connect your
turned off
MTK device to the Windows 10 calculator by USB, the device will be recognized either trough a
MediaTek Preloader USB VCOM Port
interface or as a
MTK USB port
if it is bricked or information technology has bad/corrupt firmware. The SP Wink Tool will be able to transfer the firmware to your device trough this interfaces. Make sure you connect the device
later
you press the Download button in SP Flash Tool, as the advice interface will only be alive for ii seconds if no data is beingness sent.
Download SP Wink Tool v3 & v5 – Latest versions:
http://laurentiumihet.ro/applied science/download-sp-flash-tool-v3-v5-latest-versions/
TUT
found here :
http://laurentiumihet.ro/technology…-for-32-64-fleck-drivers-installation-tutorial/
thanks
edit: i installed with digital signature disable in win 10
hi mate , in win10 64bit it says “error does not contain digital signature information”
Information technology happens to me likewise . once.
I did it with that
http://bbs.elephone.hk/thread-1037-1-1.html#.VWgkX_RAU-0
Take the drivers from at that place and make it the dingy way.
It volition say signature fails.. And then look into c:/windows/program/ mtk drivers or mediatek folder.
Open the device manager and plug in the telephone.
You will see a new USB connection. Klick there and install the drivers from the folder in a higher place. .
I did it 2 times. Then it works on win10 64bit
Gesendet von meinem Elephone P8000 mit Tapatalk
thanks alot now we tin can solve LeTv Le 1s Bootloop Issue on windows 10 .. :happytears:
pls aid…
My computer keeps giving an error code 43 (A request for the USB device descriptor failed.)
Does anyone have an idea what to do?
I used your routine simply at the end F5 is not recognized by the PC and Flash Toll does not work.
When plugging in the phone while turned off, the phone is only recognized for ii seconds and SP Flashtool doesn’t seem to be starting the download fast enough to catch on. Does anyone know how to solve the event?
Normal. Klick download in flash tools so connect the phone while belongings vol+
Gesendet von meinem P9000 mit Tapatalk
Bonjour,
connaissez vous un lien pour un pilote windows vii cascade MTK VCOM USB Drivers for 32 & 64 chip ?
par avance merci
Claude
Any ideas? Thank you <3
((((((((
In my instance it’s most a smartwatch, the DZ09. I followed the tutorial step past step and it does not piece of work. Everything goes fine just when I connect my device (powered off, of course) it plugs and unplugs (that’southward what the Windows sound reports) constantly, like a couple of times, and and then starts to charge battery (which I guess it shouldn’t).Any ideas? Thank you <three
((((((((
Hold vol+ while you plug information technology in
Gesendet von meinem Metallic mit Tapatalk
Similar threads