Logitech Artemis Spectrum G933 Not Responding After Firmware Update

The customizable RGB color on the Logitech G933 sometimes only flashes red before turning off completely. The carmine LED light can constantly blink without switching off in some cases. This error stops yous from charging and even connecting to the headphones.

Device low on accuse or a dead bombardment tin can cause the blinking red light on whatever wireless Logitech products. And so, allow’s talk about the causes and ways to fix this issue.

How to Fix Logitech G933 Flashing Red LED?

Now that we know what causes the blinking light, allow us get to how we tin can fix the problem. Here are a few lists of solutions to correct the Logitech G933 flashing red light.

Starting time the Headphones Without the Batteries

If there is some trouble with the battery where y’all cannot get the headphones to charge, you lot can get-go information technology without the battery.

Remove the Battery from the Logitech G933

To remove the battery from the Logitech, you tin follow these steps.

1. Carefully remove the encompass on the correct ear-loving cup of the headphone to admission the battery.
2. Slowly take the battery out of the socket. To remove the battery completely, you accept to detach the cable that’s continued the headphone to the battery.
3. These cables are attached with a small white connector. Carefully detach this connector.

Discharge the Headphones

The capacitor inside the headphone will hold some amount of accuse. To discharge the headphone, press the power push button four to five times.

Supply Power

To supply power to the headphone, connect them with a micro-USB.

Reconnect the Batteries

Reconnecting the batteries is fairly simple; push the white connectors until you hear a small click.

Turn On the Logitech G933

Press the power push. The red LED low-cal should stop flashing. Also, the G logo on the headphone should wink, indicating that it is charging.

Perform a Hard Reset

Sometimes, an interrupted firmware update can cause the reddish LED blinking problem. To fix this, you can hard reset the Logitech G933 by following these steps.

1. Remove the comprehend on the left side of the ear cup to open the pocket-size compartment. This small surface area holds the 2.4Ghz wireless dongle.
2. You lot will meet a small hole after y’all remove the cover. This is a reset switch.
3. Concord the reset switch using a small pin for 2 seconds.

If the headphone doesn’t reset, hold the reset switch (for 2 seconds) every 3 to 4 seconds.

Force Firmware Update

A firmware update will provide advanced operational functions to your device without any hardware upgrades. If your headphones face any problems, updating your firmware tin gear up the problem.

Note: You must have


Logitech Gaming Software


installed to forcefulness a firmware update

1. Unplug
   Logitech G933 from any power source
2. Remove
   the
   USB transceiver
   from the figurer if connected
3. Remove the battery from the headphone (Read above
   Start the Headphones Without the Batteries
   step ane)
4. Plug in the headphone to your computer using a USB-mini port.
5. Press the
   Windows
   +
   R
   key. Now, type “cmd“
   and press the
   Enter
   key
6. Type
   cd..
   and press enter. Repeat this step until you see
   C:\>
7. Type the following command and press the
   Enter
   key
   cd C:\Programme Files\Logitech Gaming Software\FWUpdate\G933
   Note: The location of Logitech gaming software may exist unlike on your computer
8. Then type command and press Enter
   G933Update_v25.exe /Forcefulness

The force update window will at present appear. Afterwards the update is consummate, plug the USB dongle onto your figurer.

Replace Dead batteries

A dead bombardment tin can cause the Logitech G933 to flash the cherry-red LED iii times and shut off. Even if nosotros charge a dead bombardment, its charge will decrease quickly. Therefore, the only solution to a dead battery is to replace it.
Follow Start the Headphones Without the Batteries step 1 to a higher place
to remove batteries from the Logitech G933.

Update/Reinstall Logitech Gaming Software

Some errors with the official Logitech Gaming Software can lead to malfunctioning hardware. Updating the software or reinstalling them completely can solve these bug.

Replace USB Wireless Transceiver

USB wireless transceiver is a small pen bulldoze-blazon device when connected, sends and receives information to and from your headphones. This is also called a 2.4GHz wireless feature. On Logitech G933, this adapter is located inside the left ear cup.

A faulty USB Transceiver can halt the information flow between your computer and headphones. If this is the instance, replacing this transceiver can solve the trouble.

Replace the Charging Cable

Another reason the Logitech G933 is non charging is a damaged charging cable. Logitech G933 uses a USB mini port to charge, which tin can get damaged fairly hands. If you cannot become the headphones to accuse, the charging cable may be at error.

Update USB Driver

The Logitech G933 uses a USB transceiver to send and receive information between the computer and the headphone itself. This USB transceiver is connected to i of the USB ports in your computer. Therefore, if this driver is not up-to-date, it cannot communicate with the Operating System.

To update the USB commuter, follow these steps.

Printing the
Windows
+
X
primal and go to
Device Manager. Expand
Universal Serial Bus Controllers,
then right-click and update everything within it. Expand the
USB Controller Manager,
then correct-click and update everything inside it.

Restart your figurer after the update is complete.

Problems with Logitech G933

If none of the above solutions piece of work, so the issue might be with the Logitech G933 itself. For case, the headphones will non charge if the USB-mini port is damaged. Yous can also take your headphones to a local electronic repair store.

You can also contact the
Logitech Back up Page.