Hp Designjet T790 Firmware Update Thru Usb

Hp Designjet T790 Firmware Update Thru Usb

Update firmware using a USB flash bulldoze or the Embedded Web Server (EWS)

This section provides data about the following topics:

Introduction

Similar to service packs for operating systems, HP provides firmware updates for printers to help address any known issues and add new features throughout the support life of the printer. To brand sure the printer is up to date, HP recommends updating the firmware for HP�Enterprise models.

note

Annotation:If you have some other HP�LaserJet model, a firmware update might not be recommended. Check the ReadMe file for these printers before performing a firmware update.

This certificate provides instructions on how to update the firmware for a single printer when the printer is in a gear up state or an mistake land.

note

Note:A �ready� country is indicated either when
Ready
displays on the command panel, or after the printer finishes initializing and all lights illuminate solid.

For instructions on how to update the firmware for multiple printers at one time using HP�Web Jetadmin, go to
Update firmware using HP�Web Jetadmin
(c03840402) (in English).

For information nearly updating Jetdirect Impress Servers using HP�Spider web Jetadmin or HP�Download Manager with FTP or the Jetdirect Embedded Spider web Server, go to
www.hp.com/get/wja_firmware.

What you lot need to know

Earlier performing a firmware update, review these requirements:

  • This printer cannot be updated using the traditional FTP, LPR, or Port 9100 methods.

  • If you have a third party solution, HP recommends contacting the vendor to make sure that the latest firmware version is compatible with the third political party solution.

  • A firmware update can require 10 to thirty minutes or more to consummate depending on the speed of the estimator and the connexion type to the printer, and any impress jobs pending in the printer queue.

  • The firmware update process requires a network connexion or USB flash drive.

  • Access to some menus on the control panel might require administrator privileges or a passcode.

About firmware downgrades

If you attempt to downgrade the firmware from a remote location to a version older than FutureSmart Bundle Version 3.7 for some newer HP Enterprise printer models, the downgrade will fail and you will receive a 99.02.32 command panel mistake and a 33.05.09 upshot log message.

This is due to a new security characteristic that requires someone to be present at the printer in order to perform a firmware downgrade and prevents HP SureStart printers from being downgraded remotely. This applies to HP Enterprise models M506, M552, M553, M604, M605, and M606. Other HP Enterprise printer models volition not experience this consequence. For more data nearly this characteristic, go to
Embedded Security features
(c04920057).

HP recommends using the latest firmware available but if a downgrade is absolutely necessary, so use the Preboot menu at the control panel to downgrade the firmware and avoid whatsoever errors. Any endeavor to downgrade the firmware remotely– or to downgrade using the Device Maintenance bill of fare, the printer�s EWS, or Spider web Jetadmin– will result in an error and the downgrade will fail. For instructions on how to downgrade the firmware for a single printer using the Preboot menu method with a USB flash drive, see
Method three: USB flash drive – Preboot menu.

Step one: Print a Configuration folio

To obtain the IP address and determine the version of firmware currently installed on the printer when it is in a fix state, print a configuration page.

Read:  Samsung Galaxy Note 2 Odin

note

NOTE:If the printer is in an error state, skip to
Method three: USB wink drive � Preboot carte.

  1. 1.

    Use one of the following methods to print a Configuration Page.


    From the Home screen on the printer command panel, follow these steps:

    1. a.

      Scroll to and open the post-obit menus:


      • Assistants


      • Reports


      • Configuration/Status Pages


      • Configuration page

    2. b.


    From the Embedded Web Server (EWS), follow these steps:

    1. a.

      Select the
      Data
      tab.

    2. b.

      Select
      Printable Reports and Pages, select
      Configuration page, and then select
      Print.

      note

      NOTE:While yous tin can view the Firmware Revision and Datecode under the “Device Information” department of the
      Configuration folio
      on the
      Data
      tab, it is recommended that you physically print the Configuration page from the printer to verify the installed firmware version.

  2. 2.

    On the Configuration Page, await in the “Device Information” department for the Firmware Revision and Firmware Datecode similar to the following example:


    • Firmware Revision:
      2131029_189663 (version installed)


    • Firmware Datecode:
      20110811 (version appointment)

Step 2: Download the latest firmware

The HP�LaserJet firmware download available from
www.hp.com
contains firmware for the printer, embedded Jetdirect (if applicable), and HP paper treatment accessories used with the printer in one user-friendly file.

  1. ane.
  2. 2.

    Select
    Drivers & Downloads, type your printer name/number in the search box, select
    Go, and so select your model from the list of search results.

  3. three.

    Scroll to the bottom of the operating arrangement list and and so select
    OS Independent.

  4. 4.

    Under the
    Firmware
    section, locate the latest firmware file, select
    Download, and so select
    Save.

    note

    NOTE:To view the latest enhancements, fixes, and other helpful information, select the firmware filename and and so select the
    Readme
    tab.

  5. v.

    Select
    Open binder
    or browse to the location where you lot saved the file, right-click the .zippo file, and then extract all files.

  6. vi.

    Notation the location of the .bdl file.

    note

    Note:The firmware file is in the format “xxxxxxx.bdl” where “xxxxxxxx” indicates the firmware file name and “.bdl” is the file extension. This file will not launch or install automatically.

Step three: Update the firmware

There are three supported methods to perform a firmware update on this printer. Use only one of the following methods to update the firmware of this printer either locally or remotely. If the printer is in an mistake land, employ
Method three: USB wink drive � Preboot menu.

note

NOTE:Depending on the firmware release version, the Preboot bill of fare method using a USB flash drive that is typically used when the printer is in an error land might be recommended even when the printer is in a ready land.

Method 1: Embedded Web Server (EWS)

The Embedded Web Server (EWS) can exist used to update the firmware remotely on a network-connected printer in a prepare land. These steps should simply be used if the printer is able to kicking to a ready state. For a USB-connected printer, skip to
Method two: USB flash drive � Device Maintenance card.

note

NOTE:If the update procedure hangs or y’all receive an incorrect/corrupt file mistake within your net browser when using the Embedded Web Server to update the firmware, the printer should nonetheless function properly just the firmware update is not complete. Try over again to update the firmware using the USB flash bulldoze method from the command console. Updating the firmware from version 11.ane to 11.three volition help eliminate the occurrence.

Read:  Download Firmware Samsung Galaxy A50 - Sm-A505f Indonesia

Follow the instructions below and/or watch the following video. If the video does non play, click
here
to view it on YouTube.


Brightcove video for EWS method

  1. one.

    Turn the printer
    Off
    so
    On, so wait until it arrives at a ready state.

    note

    NOTE:If at that place is an fault message displayed on the command panel, resolve the error showtime. If the error message persists, run into
    Method three: Update firmware using a USB wink drive – Preboot carte du jour.

  2. 2.

    Open a Spider web browser, and in the address field, type the printer IP address exactly as it appears on the Configuration Page
    and and so press
    Enter.

    The Embedded Web Server (EWS) opens.

  3. 3.
  4. 4.

    In the left pane, select
    Firmware Upgrade, and then select
    Browse.

    note

    NOTE:If an �administrator countersign must be fix” alarm displays, select the
    Security
    tab, select the
    General Security
    option in the left pane, and then under the
    Set up the Local Ambassador password
    section, reset the password.

  5. 5.

    Browse to the location where the firmware files were extracted, select the .bdl file, select
    Install, and then wait for the update process to consummate.

    note

    Notation:Practice not close the browser window until the HP�Embedded Web Server (EWS) displays the confirmation folio.

  6. 6.

    On the EWS confirmation folio, select
    Restart At present, or plough the printer Off then On once again.

    note

    NOTE:The printer will Not automatically reboot. To ensure a successful firmware update, make sure to reboot the printer.

  7. vii.

    After the printer is back online, impress a Configuration Page and verify that the new firmware version is installed.

Method 2: USB wink drive – Device Maintenance card

A portable USB wink drive can be used to update the firmware directly from the control console when the printer is in a set up country. These steps should but be used if the printer is able to boot to a ready state.

Follow the instructions below and/or lookout man the following video. If the video does non play, click
here
to view it on YouTube.


Brightcove video for USB method � Device Maintenance carte du jour

  1. 1.

    Re-create the
    .bdl
    file (downloaded previously) to a portable USB flash drive.

    note

    Annotation:USB flash drives with a CD formatted partitioning might non be recognized past the printer. You lot might need to try a different USB flash drive.

  2. 2.

    Turn the printer Off and then On, and so wait until it arrives at a set up state.

    note

    NOTE:If there is an mistake message displayed on the control console, resolve the error first. If the mistake bulletin persists, meet
    Method three: Update firmware using a USB flash bulldoze – Preboot carte du jour.

  3. 3.

    From the Dwelling screen on the printer control console, roll to and select
    Device Maintenance.

  4. 4.

    Scroll to and select
    USB Firmware Upgrade.

  5. 5.

    Insert the USB flash drive with the .bdl file on it into the USB port on the
    front end
    of the printer (remove the seal if necessary).

    note

    NOTE:If the bulletin
    No USB Thumbdrive Files Found
    displays on the control panel, make sure the .bdl file is saved to the main directory and is non inside a folder. If the message persists, attempt using a unlike USB flash bulldoze.

  6. six.

    Select the .bdl file, and so select
    OK
    or
    Upgrade.

    note

    Note:If there is more than one .bdl file on the storage device, make sure to curl to and select the correct file for the printer and firmware version.

  7. vii.

    If y’all receive a prompt to re-install the same, curl back to an older, or upgrade to the newer version, brand sure you selected the right firmware revision, and then select
    OK
    or select
    Reinstall,
    Rollback, or
    Upgrade.

  8. 8.

    Wait for the update process to complete and for the printer to automatically reboot.

  9. 9.

    After the printer is back online, print a Configuration Page and verify that the new firmware version is installed.

Method three: USB flash drive – Preboot carte

Read:  Hacking Usb Firmware Smart Tv Microprocessor Flash Tool

A firmware update might exist necessary to assistance resolve an effect for a single printer. When the printer is in an error land, the Preboot menu can be used to update the firmware directly from the control console using a portable USB wink drive.

note

NOTE:Exercise NOT use these steps to update the firmware for a printer that is in a ready country unless otherwise recommended for the firmware version of the printer. If a “Disk Total” message displays when using this method, contact the HP support center in your country/region to help troubleshoot the effect.

  1. i.

    Copy the
    .bdl
    file (downloaded previously) to a USB flash drive.

    note

    NOTE:USB wink drives with a CD formatted sectionalisation might not be recognized by the printer. Y’all might need to try a different USB flash drive.

  2. ii.

    On the control panel, open the Preboot menu.

    • Turn the printer Off and then On, and when the HP logo displays on the control panel and all three Ready, Data, and Attention LEDs illuminate solid, printing
      .

      OR

    • Turn the printer Off and so On, and when
      1/8
      displays beneath the HP logo on the command panel, touch the logo.

  3. 3.

    Ringlet to and select
    Ambassador.

    note

    Note:To scroll on the control console, employ the touch screen scrollbar or the upwards/down arrow buttons. If indicated on the touchscreen, yous will need to use the
    3
    (up) and
    ix
    (downwardly) keys on the control panel to whorl.

  4. 4.

    Scroll to and select
    Download.

  5. 5.

    Insert the USB flash bulldoze with the
    .bdl
    file on it into the USB port on the
    front
    of the printer (remove the seal if necessary).

    note

    Notation:If the message
    No USB Thumbdrive Files Found
    displays on the control panel, make sure the .bdl file is saved to the main directory and is not inside a folder. If the message persists, try using a different USB flash drive.

  6. 6.

    Gyre to and select
    USB Thumbdrive.

  7. 7.

    Select the .bdl file, select
    OK
    or the
    6
    key, and so wait for the update process to complete.

    note

    NOTE:If there is more than one .bdl file on the storage device, make certain to scroll to and select the correct file for the printer and firmware version.

  8. eight.

    When
    Complete
    displays on the control panel, select the back arrow

    until
    Continue
    displays, select
    Continue, then wait for the printer to automatically reboot.

  9. nine.

    After the printer is dorsum online, impress a Configuration Folio and verify that the new firmware version is installed.

Hp Designjet T790 Firmware Update Thru Usb

You May Also Like