How to Upgrade Firmware Phantom 3 Advanced
In this article, nosotros will depict the steps you must take to perform a Phantom 3 firmware upgrade. Information technology doesn’t thing if you own a Professional, Advanced or Standard version of the Phantom 3. We will help yous get it upgraded.
It’due south a good idea to update the firmware before you become have off for your maiden flight. I followed these steps and successfully upgraded my phantom 3 pro. The times noted below are in reference to the initial firmware upgrade after receiving the new phantom 3. If yous take problems with the upgrade read the mutual solutions at the cease of this mail service.
Here’s what’s needed to exercise a Phantom three firmware upgrade:
- A charged
Phantom three Pro
or
Advanced
(I unremarkably upgrade with a fully charged battery. Technically y’all tin can apply a >l% charged bombardment, but it’s better to play it safe.) - Charged Remote Command or Transmitter (Tx)
- microSD card
- microSD to SD adapter or card reader. I use the one that came with my
Lexar 64gb microSD card.
To upgrade the Quadcopter/Drone itself follow these steps:
- Charge your DJI Phantom 3 Pro or Advanced
- Accuse your Remote Command
- Accept microSD carte from Phantom 3
- Insert it into a cardreader, and plug into your figurer
- Fill-in contents of your microSD bill of fare
- Download the firmware from the official downloads:
- Exist sure you cull the firmware meant for your version of the Phantom 3! (also: note that the ane.ane.6 version isn’t the current version)
- Extract the .nada file
- Place the .bin onto the root of the SD Card
- Safely remove the microSD carte du jour from the computer
- Make certain the Phantom three is powered off
- Make certain the Remote Control is powered off also
- Insert microSD card with Firmware .bin file into the Phantom iii
- Ability on Phantom 3 alone
- (Note it may take 25 min for firmware upgrade)
- During the Bootup Stage (first 60 sec) it will initialize the gimbal and do a normal startup. After the minute it volition beep in a design such as “Beep-Beep-Beep-Beep-Pause” and this will exist repeated during the whole firmware upgrade. The good news is its not the Startup Beeps (ESC’s & Motors) just something on the gimbal board. Information technology’s much quieter than the startup beeps. During the process the front LED indicators are solid red, and the Shipping Status Indicator LED’s flash yellow.
- (Updating to i.4.0010 i got the normal standard bootup beeps four times effectually the 13th, 14th, 15th and 17th infinitesimal into the process) Afterwards each information technology just connected it’due south normal “Beep-Beep-Beep-Beep-Interruption” sounds.
- (Updating to 1.4.0010 at 31min the beeps got a bit distorted for a few seconds then returned to normal)
- Later on about (thirteen minutes in my case for one.1.0006 and 32 minutes for i.4.0010) The beeps will change to a “Beeeeeeeep-Beep-Beep-ShortPause” tune. This means the firmware upgrade is consummate.
- Close down your Phantom 3
Note: The Camera Processing Board, Gimbal and Camera can be hot to the bear on, happens to me as well. Just exist certain to let it properly absurd before flying or putting it away. - Accept the microSD card from the Phantom 3 and insert it into your microSD adapter again or other bill of fare reader and check the contents on a reckoner.
- Open the .txt file (in my case P3X_FW_RESULT_AB.txt)
- Check for success bulletin. (If you don’t receive a success message attempt the upgrade again
Afterward reformatting your microSD carte du jour and re-downloading the firmware. As always backup your data before reformatting)
To update the Remote Control:
Either update using the DJI GO App:
- Make certain the DJI Go App has been updated to v.1.2.0 before trying this upgrade. If in that location is an upgrade available for your remote command and your electric current version of the Go App allows for it to be installed the System Status Bar in the Camera View will flash several times.
- Tap the System Status Bar.
- Tap Overall Condition.
- Tap Download the firmware update bundle to download and update the firmware. Y’all can track the progress in the DJI Get App. The status LED on the remote command will glimmer blue during the update and blink green once the update has been completed successfully.
Or to upgrade using a USB Drive (only option until you go to v1.3.xx. Run into what happened to me below instructions):
- Identify the same firmware file onto the root directory of the USB drive (in my example i moved all files off the bulldoze then only the firmware file was on the device).
- Safely remove the USB bulldoze from your reckoner.
- Make certain both the Remote Control and the Phantom 3 are turned off.
- Place the USB drive into the USB port of the Remote Control.
- Plow on the Remote Control.
- Subsequently about 25-30sec it will commencement beeping. During the upgrade, it tin beep in unlike intervals and patterns. Equally long every bit the Status LED is Bluish the upgrade is in progress!
- Once the beeping stops (took in my case 1m33sec for 1.1.0006 and a bit longer for 1.3.20) and the Status LED shows solid green the upgrade is complete.
- Turn off the Remote Command and remove the USB drive.
I happened to have the 1.1.0006 firmware on my remote control when i tried to update to one.4.0010. My DJI Go App told me I couldn’t update with the mobile App and the 1.four.0010 firmware on a USB stick caused the following result:
==========2015.09.08 nineteen:12:03==========
Packet: /mnt/usb/P3X_FW_V01.04.0010.bin,
Result: Abort
The firmware on the SD card is identical to or older than the current firmware on the remote controller.
My Solution was to install the 1.3.20 firmware on the remote command.
Afterward the above steps are completed y’all will have the current firmware on your phantom three. After each firmware update i highly recommend resetting the IMU and recalibrating the gimbal. Of course the first flight should and then be started with a compass calibration.
Common Bug & Fixes:
Remote Control shows cyan Status LED and won’t demark with Phantom 3:
- If normal bind procedure doesn’t work, here are the steps to do a hard reset on your remote control:
- Power Cycle your remote control
-
Push and hold
all of the following buttons at once (meet image beneath)- C1
- C2
- The Video Record Button
- The Camera Settings Punch
Did this article aid yous out? Requite us a like on
facebook!
