Epson L805 Printer All Lights Blinking Solution
Diagnosing the Problem
Troubleshooting printer problems is best handled in ii steps: first diagnose the problem, then apply likely solutions until the trouble is fixed.
The data that you need to diagnose and solve nearly common problems is provided past online trouble solving, the control panel, the status monitor, or by running a printer functioning check. Refer to the advisable section below.
If yous have a specific problem relating to print quality, a printout trouble not related to impress quality, or a paper feeding problem, or if the printer does non print at all, refer to the appropriate department.
To solve a problem, you lot may need to cancel press.
Error indicators
Yous tin can identify many common printer problems using the lights on your printer. If the printer stops working and the lights are on or flashing, use the following table to diagnose the problem, then follow the recommended corrective measures.
|
Lights |
Trouble and solution |
|
|
|
Paper out |
|
|
No paper is loaded. |
Load paper into the sheet feeder, and then press the |
|
|
CD/DVD tray error |
||
|
When printing on a CD or DVD, the CD/DVD tray is not inserted. |
Insert the CD/DVD tray in the printer and press the |
|
|
Multiple feed mistake |
||
|
The printer has fed more than than one sheet of newspaper at a time. |
Make sure you set the front tray to the paper position. Then, load paper in the sheet feeder and printing the |
|
|
|
Paper jam |
|
|
Paper has jammed in the printer. |
|
|
|
CD/DVD tray jam |
||
|
When press on a CD or DVD, the CD/DVD tray is not ejected. |
Pull out the CD/DVD tray and press the |
|
|
|
Ink level reaches the lower line |
|
|
Ink level may accept reached the lower line. |
To ostend the actual ink remaining, visually check the ink levels in the printer’south ink tanks. |
|
|
|
Ink level is low |
|
|
Ink level may be low. |
You may continue press. To confirm the actual ink remaining, visually bank check the ink levels in the printer’s ink tanks. Epson recommends to proceed using the printer until the ink level reaches the lower line so that the ink tank can be refilled with the entire contents of a new ink canteen. |
|
|
|
Cover open |
|
|
The printer cover is open. |
Shut the printer comprehend. |
|
|
Front tray error |
||
|
The forepart tray is not in the correct position. |
Before turning on the printer, set the front tray to the paper position. |
|
|
Flashing alternately |
Maintenance |
|
|
The printer’s ink pads are at the cease of their service life. |
Contact Epson back up to replace ink pads. |
|
|
|
Unknown printer error |
|
|
An unknown printer error has occurred. |
Turn off the printer. Open the printer cover and remove any newspaper or other obstructions from the paper path. And so plow the printer back on. If the mistake does non clear, contact your dealer. |
|
newspaper button. The printer resumes press and the light goes out.
= on,
= off,
= flashing slowly,
flashing fast
Condition Monitor
If a problem occurs while printing, an fault message volition appear in the status monitor window.
When you need to refill an ink tank, click the
How To
push button on the window, and follow the instructions.
To confirm the gauge ink levels, meet the following section:
Encounter
Using EPSON Status Monitor iii
(Windows)
If an fault message appears indicating the printer’southward ink pads or ink tubes are nearing or are at the end of their service life, contact Epson support to supersede them. When the printer’south ink pads are saturated or the printer’s ink tubes are at the finish of their service life, the printer stops and Epson support is required to continue printing.
Running a printer operation check
If yous are unable to determine the source of the problem, run a printer performance check to help you determine whether the problem comes from the printer or your computer.
Earlier running a printer operation bank check, brand sure the front tray is in the paper position.
To run a printer operation check, follow these steps.
|
Brand sure both the printer and computer are turned off. |
|
Disconnect the cable from the interface connector of the printer. |
|
Make sure that A4 size paper is loaded in the sheet feeder and that the CD/DVD tray is not inserted in the printer. |
A test page prints showing a nozzle check pattern. If the blueprint has gaps, you need to make clean the print caput.
If the test page prints, the problem probably lies in your software settings, the cable, or your computer. It is too possible that your software may non be installed correctly. Try uninstalling your software and reinstalling it.
Run across
Uninstalling the printer driver
If the exam page does non print, yous may accept a trouble with your printer. Try the suggestions in the following section.
See
The Printer Does Not Print
