Does the Lightify Bulb Need to Be on During Firmware Updates

The mail service-obit steps draw the OTA (= Over The Air) firmware update of OSRAM (also known every chip Sylvania) / Ledvance devices (In this case a smart plug is updated).

On 2020-03-09 Osram (also known as Sylvania) has decided to shut downwardly server support for smart lamps from the Lightify lighting system inside 18 months. This means Osram (also known as Sylvania) volition therefore be shutting down the cloud server for controlling the Lightify gateway on Baronial 31, 2021. And then updating the devices via an Osram lightify gateway will be no longer possible in the nearly futurity.

However at that identify is a workaround using deCONZ and RaspBee or ConBee as explained beneath.

Requirements:

– Raspberry Pi three Model B (or B+) or an Raspberry Pi four Model B + Power Supply (at to the lowest degree two.5A)

– 32 GB Micro SD Card (Application Class ii)

Steps:

i.) Connect the Osram On/Off Plug via Phoscon/deCONZ equally mentioned
here

two.) Check the deCONZ GUI (via visiting
http://phoscon.de/app) and annotation the electric current installed firmware version (and then you lot know the update worked)

3.) Download a VNC Tool similar RealVNC Viewer from hither and utilize information engineering to connect to the desktop (User: Pi & Countersign: raspbeegw; for more info`s run beyond
here)

4.) Commencement the deCONZ GUI

five.) Select the standard OTAU plugin via the menu bar in deCONZ via Bill of fare du jour -> Plugins -> STD OTAU Plugin and Switch to the “STD OTAU Plugin” tab on the bottom

Note: If the device y’all wish comes upward with Version: 0x00000000 or Prototype: 0x0000 equally seen in my pic printing the query button and await some minutes (or remove the plug from the wall socked await some min and re-plug information technology)

vi.) Select the device in the list yous wish to update (cheque the MAC Accost) and brand a annotation from the Image proper noun

8.) Brand sure the device is still selected (bluish underline), then select the OTAU update file on your PI and press on the update button

9.) deCONZ will now perform a update from the device

Annotation: The procedure tin take upwards to fifteen-thirty minutes until completion (the device will restart itself automatically after information technology finished the update)

x.) Later the device is dorsum, y’all can meet that the version number change from 0x01020490 to 0x01020509

11.) If yous open upwards the deCONZ GUI (via visiting
http://phoscon.de/app) and check now the version, information technology should take changed:

Annotation: If the version is nevertheless the same, and so reset the plug and re-pair it. Then the version will exist updated.

Notes:

Proceed noted that at that place are are tree dissimilar Osram Plugs:

i.) The Osram Lightify Plug

Which comes upwardly equally:

• Epitome: 0x000a
• Epitome manufacturer code: 0x110C
• Node Descriptor advertises manufacturer code: 0xBBAA

Its unclear if those devices could exist updated. Equally I practice non have such a device i too couldn´t banking business organization bank check it on my ain.

2.) The Osram Smart+ Plug (Zigbee 3.0?)

Which comes upward as:

• Epitome: 0x0027
• Epitome manufacturer lawmaking: 0x110C
• Node Descriptor advertises manufacturer lawmaking: 0xBBAA
• Known as: Plug01 OnOff MK

on the back is oft i from the following written:

• Smart Plug AB32570
• Smart Plug+ AB3257001NJ
• Made in Prc x3419
• Made in China x2019
• Fabricated in Mainland communist mainland china x3118

The older Osram firmware version V1.04.12 and V1.04.90 where successfully updated to the Ledvance V1.05.09

3.) The Osram Ledvance Plug

on the dorsum is ofttimes ane from the post-obit written:

• Smart Plug AB32570
• Made in Red china x3419

Troubleshooting 01:

I had ane device which withal comes upwards equally Version: 0x00000000 with Image: 0x0000 regardless what I tried. Every bit I was sure its the Osram Smart+ Plug, I load the Ledvance firmware and flashed version V0.twenty Build 509. To perform that I pressed 2-3 times the update button until the update started.

Troubleshooting 02:

Afterward the update my Philips HUE wasn´t whatsoever longer able to find the devices. I removed them all from the wall charger, waited ii hours and plugged them in. All my devices could then be constitute without any issues. And so if you freshly upgraded device isn´t any longer working. Effort to continue information engineering unplugged for +2 hours and and then attempt to pair them once again.

Known firmware and changes:

Plug01 OnOff MK:

v1.04.12 / 1020412 by Osram

v1.04.90 / 01020490 (2017-08-xv?) by Osram

• Stock-still possible malfunction in example of more systems working close
• Stock-still possible cake status in instance of many colour change commands in a short time
• Stock-still outcome related to the configuration of the light level and colour reports
• Increased OTA upgrade reliability
• Improved conversion between Hue/Saturation and ten/y colour notation upon color alter commands

01020509/01020510 past Osram

• Optimized pairing timing
• Added custom control for enabling/disabling touchlink
• Fixed issue related to the network joining in multi-promise scenario
• Improved OTA prototype query machinery
• Stock-still possible security issue
• Improved timing identification through touchlink letters
• Improved lamp brightness on the dynamic scene activation
• Added custom commands to set up the lamp country afterward on OTA upgrade and afterward a ability bike
• Stock-still wrong lamp behavior switching from colour dynamic scene to color temperature dynamic scene

v1.05.09 / 01020509 (14 March 2019) past Ledvance

• Stack upgrade
• Improved network operation

Update:

Some users asked if the same is likewise possible using a windows PC, and then hither is a small update focusing on a windows PC (meet too here).

one.) Download and install the latest deCONZ Version on your Windows PC (at the moment this is version ii.05.71)

two.) Plug the ConBee USB Stick into your Windows PC

iii.) Beginning the deCONZ GUI

iv.) Select the standard OTAU plugin via the carte bar in deCONZ via Card -> Plugins -> STD OTAU Plugin

5.) Switch to the “STD OTAU Plugin” tab on the bottom

6.) Select the device in the list you lot wish to update (check the MAC Address) and brand a note from the Prototype proper name

vii.) Become to the Ledvance Firmware Update site, enter the epitome proper proper noun and printing search [Optional y’all lot tin can effort the following original Osram firmware update site]

viii.) Download the latest OTAU file via the push latest and store that on your PC

nine.) Make sure the device is even so selected, then select the OTAU update file on your PC and press on update

Notation: The process tin tin take upwards to five-ten minutes until completion (the device volition restart itself)