Does Samsung Have a Firmware Update for the Dvd Recorder and Vcr — Model # Dvr Vcr320

HOW TO Eject THE CASSETTE TAPE (If the record is stuck in the unit of measurement)

1.) Plow the Gear Worm [one] clockwise in the direction of arrow with a screwdriver.

(Other method ; Remove the screw of Motor Load Ass’y, Separate the Motor Load Ass’y)
2) When Slider Due south, T approaches the unloading position, rotate holder Clutch counterclockwise after inserting screwdriver in the frame’s bottom pigsty in club to wind the unwound tape.

(If you rotate Gear Worm [i] continuously when tape is unwinding, you may cause tape contamination by grease and tape damage. Exist sure to current of air the unwound tape with the unit of measurement in the horizontal position.)
three) Rotate Gear Worm [1] clockwise using a screwdriver until the machinery is in the squirt country. R
Mode switch (program switch) associates bespeak

Mode switch (plan switch) assembly indicate

When installing the donkey’y deck on the Chief PCB, be sure to align the assembly bespeak of manner switch.

Remote Control:  Part number – AC59-00053A

Software Update

Drive Firmware Update

Samsung volition ofttimes support software update to improve the performance of DVD Recorder & VCR to the latest status, through Samsung Internet Site. (www. samsung.com)

How to brand an update disc

Write the downloaded file onto a blank CD-R or CD-RW disc, using the following settings :

one) You lot take to download a new file through Samsung cyberspace site. (www.samsung.com)
ii) Write the file to disc using the CD-RW of your computer.

• Recommended Application Programme – Nero Burning / Easy CD Creator ..etc
• Option
– Name : SDM2224
– Extension name : “*.REC”
– Multisession : No Multisession
– File name length : Max. of 11 = 8 + 3
– Format : Manner ane
– Grapheme set : ISO 9660 or Joliet Format
– CD Shut & Disc at one time
– Label : RAMBO

It is very important : please read the below notice below earlier updating your unit.


The following events may interrupt the update process and MAY Result IN PERMANENT DAMAGE TO THE Unit of measurement WHILE UPDATING

Unplugging the power string.
Power Outage.
Dirt or Scratches on the disc.
Opening a disc tray during processing.

Press
OPEN/CLOSE
to open the disc tray.
ii) Insert the update CD-R disc with the software update, characterization facing up.
3) Press
OPEN/Shut
to close the disc tray.
* It takes about ane~ii minutes earlier the message below appears.

If you don’t see the message above, try another disc. More often than not, this is acquired by disc quality and by disc creating trouble.

iv) Printing the
ENTER
push on the remote control.

You volition come across “LOAD” on FLT Brandish.

5) It takes about 1~2 minutes to complete the update.
The message below will be displayed in the screen later on update is completed and the tray will open automatically

6) After removing the update disc, plough off the unit of measurement with power button.
And there later plough on the unit with power push and then the volition be closed.
The bulldoze firmware is at present completed.

Flash Update

How to brand an update disc

Write the downloaded file onto a blank CD-R or CD-RW disc, using the following settings :



one) You lot take to download a new file through Samsung internet site. (www.samsung.com)
2) Write the file to disc using the CD-RW of your calculator.

• Recommended Awarding Program
– Nero Called-for / Easy CD Creator ..etc.
• Option
– But single session
– CD shut & disc at once
– ISO 9660 or Joliet format
– Extension name : “*.RUF”
• In order to increase disc playability, add together a dummy file (over 100MB) together with the latest plan.
(The dummy file can be used any kind of file except MP3 file etc. which can be played in the unit of measurement and we recommend to use a file within extension name as “*.dmy”, which can exist changed from original one.)

It is very important : please read the beneath notice below earlier updating your unit.
The following events may interrupt the update process and MAY Effect IN PERMANENT DAMAGE TO THE Unit WHILE UPDATING

Unplugging the power cord.
Ability Outage.
Dirt or Scratches on the disc.
Opening a disc tray during processing.

Press
OPEN/Shut
to open the disc tray.
2) Insert the update CD-R disc with the software update, label facing up.
iii) Press
Open up/Shut
to shut the disc tray.

* If you don’t see the message beneath, endeavor another disc.
Mostly, this is acquired by disc quality and by disc creating problem.

four) Press the
ENTER
push button on the remote control

5) It takes nearly five minutes to complete the update.
The message below volition be displayed in the screen afterwards update is completed and the tray volition open automatically

* If the message to the left isn’t displayed after 10minutes and the unit of measurement is no longer functioning properly, contact a Samsung authorized service center.

half dozen) After removing the update disc, turn off the unit with power button.
And there after turn on the unit with power button and then the will be closed.
The Flash update is now completed.

SMPS schematic