Dji Inspire 1 1.11.50 Vs 1.9 Firmware Update
Hello everyone! I accept an Inspire 1 V1 given to me past a relative but I can’t seem to update it to the latest firmware, I accept been trying to update it to the latest firmware V01.11.01.50 (X3) but information technology does non make that usual gimbal sounds when updating. This is also the same firmware I used on one of my Inspire i and information technology does update successfully. Peradventure somebody here tin assist me solve this problem. Thanks in advance.
Here are the firmwares installed:
App. three.1.11 |
|
2017-10-21
|
Any DJI reps who can chime in? |
|
2017-10-21
|
OK become to here and download version one. nine first and so endeavor to update
http://www.dji.com/inspire-1/info#downloads
then mail service the hidden log file from the SD card nether the MISC/LOG folder, you will demand to enable view of subconscious files on your estimator to see this, postal service it here and then we tin go from there |
|
2017-10-22
|
The plus sign would advise the update has not completely finished, you may have to connect to the internet to complete the process.
This is what DJI Jamie says about it. “If this happened after a firmware update, it means that the unit registers that there has been an accepted change in firmware. If your mobile device is connected to the internet/ information, please give the Become app ten-fifteen minutes or so then power cycle the aircraft and RC to reflect the changes in firmware numbers. Subsequently that, your unit of measurement will show the correct firmware version. Having the plus at the terminate is not a cause for business organisation and information technology will address itself.” Marking Yard. |
|
2017-10-22
|
I’ll try it guys, thanks. |
|
2017-10-22
|
I tried it 3 times, every time checking if at that place is log made and if in that location is none I formatted once again and downloaded firmware once again ( three times ) but however no logs made. I also ready the figurer to bear witness all subconscious files. |
|
2017-10-22
|
Are you using a MAC or PC to load the Bin File. If you lot can use a PC. Be sure to format ( SD) on the PC as well . brand sure only the Bin file is loaded. After you load the Bin file to the Sd card be certain and look at the SD card and make sure NOTHING else is on in that location .
Also wonder if y’all demand to load 1.3 start then jump to the other updates. Here is a link to older files . Besides accept 5 minutes and read my tips page . It might requite you a inkling on what is going wrong . http://www.panorobot.com/dji/inspire_firmwares.htm donnie |
|
2017-10-22
|
Ok and so here’s the update, finally I updated the AC to 1.11.01.fifty by using the x5 camera that I have only the x3 nonetheless does not do anything. Tin information technology exist that the x3 is defective? Is there anyway to update the x3 without using a SD card? Correct at present the firmwares are
App. 3.1.11 |
|
2017-10-22
|
Any suggestions from DJI mods? |
|
2017-10-22
|
When you try to update the X3 do you lot become any data at all on the SD menu result log ? If you practice please check lines of code 0800 and 1500 and allow me know what they say . Also did you happen to endeavour the X3 photographic camera and the i.3 Bin file ? Just wondering if the Update did not take on the camera and y’all may have to load the one.3 file first then update to the latest 1 . Nosotros really demand to run into the data on the Hidden file if at all possible . The x3 at minimum does the startup dance correct ? Tin can you see video alive from it also ? Might not with the latest update to the Air-conditioning itself merely simply wondering. donnie |
|
2017-x-23
|
No, in that location’s no log on the x3. I tried the firmware ane.three and also tried the 1.nine. I besides looked at the hidden files merely naught there too. The camera does its normal dance and I tin can run into video but after virtually 23 seconds the screen of turns to blackness then bluish and then black again with a dji logo. |
|
2017-10-23
|
These goes on and on every 23 seconds. |
|
2017-ten-23
|
It sounds like the X3 may be prophylactic ducked. |
|
2017-10-23
|
Rubber ducked? What’s that? |
|
2017-10-23
|
Please install the X3 on your drone and bank check if it starts self-checking when y’all turn on your drone. Did you try another SD card in your X3? |
|
2017-10-24
|
Cheers for chiming in DJIELEKTRA, yes the x3 does it’s usual self Check and have used dissimilar SD cards also. Only sound I can hear after x3 self Check is D—DD around every 27seconds. |
|
2017-10-24
|
Thanks for chiming in DJIELEKTRA, yes the x3 does it’due south usual cocky Cheque and have used different SD cards as well. Only sound I can hear later on x3 self Bank check is D—DD around every 27seconds. |
|
2017-ten-24
|
Dji Elektra, what practise you recommend next ttime exercise? |
|
2017-10-24
|
Is there any way to update the firmware without using the AC? Is it possible to use the micro USB on the dorsum of the X3 to update the firmware? |
|
2017-10-24
|
DJI Elektra??? |
|
2017-10-25
|
Any dji reps??? |
|
2017-10-25
|
Sad for the late response. Just back from holiday, you lot can only update your I1 through SD card. The micro USB on the back is for exporting flight information. If the X3 first self-check, it means that there is zippo wrong with the connection. Can you connect your drone with your app? Any message? |
|
2017-x-26
|
Aye I tin connect the drone to my app and I can control the the camera and gimbal too. Only effect is that video gets cut off effectually every 27 seconds and a D…DD sound is emitted by the gimbal and video resumes afterwards that. If I tape a video information technology gets cutting off by this issue, it seems like the gimbal/camera is rebooting every 27 seconds. Message on the app says to upgrade to latest firmware. |
|
2017-10-26
|
Message on the app says to upgrade camera to latest firmware. |
|
2017-10-26
|
If you failed to update to the latest firmware of X3 many times, I would recommend you send it back for check. When you update your X3, if you hear DDDD, information technology ways that your camera is updating. Delight wait and encounter if it can update successfully, you can check the result from the log in SD carte du jour . |
|
2017-10-26
|
I thought the sound process when updating firmware is as follows:
D.D.D.D.D.D.D.D.D.D. When it’due south ready to update. |
|
2017-10-27
|
Please wait patiently for the update process and check the log in the SD bill of fare. |
|
2017-x-27
|
Withal nil is happening. In that location’south no lg on the SD card and I am using the original SD bill of fare. Could it be that if the firmware is on i.two.1.06 it can’t be updated to the latest firmware considering you lot take to update to some other firmware offset before you can update to the latest? |
|
2017-10-29
|
In this example, I would recommend you send it dorsum for cheque. Something wrong with your X3. Here is the link: |
|
2017-10-29
|
WITH THE X3 CAMERA : How to View Subconscious Files: Tool to diagnose No bespeak and SD Issues
Have you tried to load version i.3 to the X3 camera ? Jsut wondering if the photographic camera never was updated to version 1.iii and is stuck at version 1.two.1.06 Here is the file you volition want at the bottom of this link . Here is link to a 1.3 file , be sure y’all ONLY LOAD THE BIN FILE TO THE SD Carte du jour . You will come across 4 files open up , only 1 is the bin file. do information technology just like when you updated the AC to version i.11 using the x5. donnie ****If the bin file ane.3 is not the problem then more than likely yous take a fialed “Video Encoder ” module on the X3 camera and will need to be sent in. The only glimmer of promise i encounter is the photographic camera (X3 ) is on very onetime Fw and may merely need to be updated to version 1.3 and then from there to the latest FW and and so you should be expert to go . If the one.three Bin file volition not load and you lot get no log then more than than likely thats the problem . Cost is about ane -300 dollars or you may wish to get ane off eastward bay , seen some pretty good deals lately . |
|
2017-10-30
|
Ok I’ll try upgrading information technology again with the link yous shared, I promise this fourth dimension it volition work, thanks. |
|
2017-10-31
|
Ok, adept luck . donnie |
|
2017-11-one
|
Still no dice, I tried also the other one the ane.02.02.17 but it seems that it’s corrupted or something, I tin can’t unzip it. Yes I can command the aircraft and data on is transmitted from Air-conditioning to remote it’s simply the video keeps cut off every 27 seconds. |
|
2017-11-three
|
I ask my uncle what he did to the aircraft, he said that he downgraded the firmware to one.2.1.06 using firmware from panorobot.com. He said he added a new binder with a folder name of WM610_FW_DEBUG to the SD card together with the firmware one.2.ane.06. |
|
2017-xi-5
|
Ok please read my link with tips on how to update . Yous need to get the BIN file merely ( 1.3 ) loaded for that photographic camera to wrk , I recall you are not loading the correct file . https://forum.dji.com/thread-72851-i-ane.html Here is a pic on what the file should look like when you get prepare to drag and drop to a Thumb drive. If this does not work and you get no data to the SD card thden more than likely the Camersa will demand to go in for repair. donnie
|
|
2017-eleven-6
|
Still no luck. Same affair happens, no gimbal update sounds and no data on SD card. Any idea how much would be the repair toll for it? |
|
2017-11-11
|
Lately this repair has been around 275 USA dollars. You may want to find a used i on e bay . You could transport it in for an estimate, I think that will still cost almost 75 dollars to do that, or if you are lucky they encompass it under warranty sometimes depending on what needs to be done . skillful luck donnie |
|
2017-xi-12
|
Please assistance, after firmware update on my inspire 1 my remote won’t respond to app and AC |
|
2019-8-10
|
Please is there a special thumb bulldoze for RC firmware update? I accept tried many times times only it appears RC doesn’t even read the drive. Whatever help on what to do? |
|
2019-8-10
|
I have the same problem with my inspire 1 also, i updated Ac with the latest firmware V1.11.01.50 and then remote unable to connect to app and AC. Whn I try to relink the AC to RC i encounter scarlet/green light flashing very fast on RC. What should I exercise, any help will be very appriciated. |
|
2019-8-x
|