Always Connected to Hp Printer 415 Wireless
Z7_3054ICK0KGTE30AQO5O3KA30N0
hp-concentra-wrapper-portlet
Actions
HP Printers – Troubleshoot a Wi-Fi Printer Connexion
This document is for HP printers with a wireless connection.
If the estimator is unable to detect the printer over a Wi-Fi connectedness, restart the printer, figurer, and router, and then make a new connection.
note:
When troubleshooting a connection to your wireless network, make sure you are connecting your printer directly to the wireless network and not through a wireless extender.
Step i: Restart your devices
To prepare your printer for a wireless connexion, restart the printer, reckoner, and router.
-
Turn the printer off, and then wait 10 seconds.
-
Disconnect the printer ability cord from the printer.
-
Plow off the reckoner or the device y’all are trying to print from.
-
Connect the printer power cord to the printer, and so plough on the printer.
-
Disconnect the ability cord from your wireless router, and and then wait ten seconds.
-
Reconnect the power string to the router.
note:
Wait until internet service is restored. Internet service is interrupted while the router is off.
-
Plow on the calculator.
Your printer and network are ready to brand a new connexion. Proceed to the next footstep.
Step two: Connect the printer to your network
Connect the printer to your network using the HP wireless setup wizard (for printers with a touchscreen command panel), WPS (if supported by your router), or the HP Smart software.
note:
You cannot connect to a printer over restricted guest networks, such every bit those in many hotels and dorm rooms. Instead, connect direct to the printer’s Wi-Fi Direct connection, if bachelor.
Connect a printer that has a touchscreen control panel
Use the Wireless Setup Wizard to establish a wireless connection between your printer and network.
-
From the habitation screen of your printer command panel, bear on the
Wireless
icon
.
-
Touch the
Setup
icon
.
-
Affect
Restore Network Defaults
or
Restore Network Settings, and so touch
Yes
to confirm your selection. -
After the default network settings are restored, impact the dorsum arrow, touch
Wireless Settings, and then affect
Wireless Setup Wizard.The printer searches for available networks.
-
Touch on the proper noun of your wireless network.
-
If your wireless network does non display in the list of wireless networks, touch on
Enter New Network Name, and then type the proper noun of your wireless network.notation:
Type the exact network name, including any capital and lowercase letters.
-
Type your network security password (WEP or WPA key), and then touch
Done.In one case the printer is connected, the blue Wireless low-cal (or wireless icon on the bill of fare) stops blinking and remains on.
If the printer fails to connect, continue to the next footstep.
Connect a printer that does not have a touchscreen control panel
Utilise Wi-Fi Protected Setup (WPS), HP Smart, or temporarily connect a USB cable to establish a wireless connection between your printer and network.
Connect the printer with WPS
Wi-Fi Protected Setup (WPS) is an like shooting fish in a barrel way to connect a Wi-Fi device to a Wi-Fi network that supports WPS.
-
Locate the WPS button on your router,
only exercise non press information technology however.If your router does not support WPS, do not continue with these steps. Use another method such equally connecting the printer with HP Smart app.
-
Turn on the printer. If the printer is in slumber mode, press the
Cancel
button to wake the printer. -
Press and concord the
Wi-Fi
push on the printer for 5 seconds. For HP Tango printers, printing and hold the
Wireless
button and
Power
button at the same time for five seconds. -
On the router, printing and hold the
WPS
button for 3 to 5 seconds or until information technology shows that the WPS connection process has started.note:
The printer stops searching for a WPS connection 2 minutes after the wireless button is pressed. If you were unable to press the
WPS
button inside that timeframe, attempt these steps once again.Once the printer is continued, the bluish Wireless lite stops blinking and remains on.
If the printer fails to connect to your wireless network, try another method.
Connect the printer with the HP Smart app (Windows 10)
Use the HP Smart app to connect the printer to your wireless network.
-
Make sure your figurer is connected to your wireless network.
-
On your reckoner, download and install the
HP Smart
app (in English) from the Microsoft store. -
Turn on the printer.
-
If the printer is in slumber mode, press the
Cancel
push on the command panel. -
Reset the printer network settings.
-
For most HP printers: Press and concord the
Wireless
and
Cancel
buttons until the Wireless and Power lights glimmer. -
For HP Green-eyed 6000, Pro 6400, DeskJet Plus IA 6000, and 6400 All-in-One printers: Press and hold the
Wireless
button on the back of the printer for five seconds until the Border lighting flashes majestic. Information technology might take several attempts before the lighting flashes. -
For HP Tango printers: Press and hold the
Wireless
push on the dorsum of the printer for five seconds until the front light flashes blue. -
For HP Laser (not LaserJet) printers: Press and concur the
Wireless
button until the Attention low-cal blinks. The printer might restart.
Any network settings on the printer are now reset. Your printer remains in setup mode for 2 hours.
-
-
On your computer, open up HP Smart, and so click the
Printer
icon
.
-
Click
Set Up a New Printer, and so click
Go on.HP Smart searches for printers on your wireless network.
-
Select your printer, and and then click
Proceed. -
When prompted, type the WEP or WPA key (network password).
-
Afterwards the printer connects to your wireless network, click
Continue, and and so click
Leave Setup.Once the printer is continued, the blue Wireless light stops blinking and remains on.
If the printer fails to connect to your wireless network, try some other method.
Connect the printer with the HP Smart app (Mac Os X)
Use the HP Smart app to connect the printer to your wireless network.
note:
The HP Smart app is simply available for select printer models with Mac computers.
-
Brand sure your reckoner is connected to your wireless network.
-
Plow on the printer. If the printer is in sleep manner, press the
Abolish
button on the control panel. -
Reset the printer network settings.
-
For most HP printers: Press and hold the
Wireless
and
Cancel
buttons until the Wireless and Power lights blink. -
For HP ENVY 6000, Pro 6400, DeskJet Plus IA 6000, and 6400 All-in-One printers: Press and concord the
Wireless
push button on the back of the printer for five seconds until the Edge lighting flashes majestic. It might take several attempts earlier the lighting flashes. -
For HP Tango printers: Press and hold the
Wireless
button on the back of the printer for five seconds until the front calorie-free flashes blue. -
For HP Light amplification by stimulated emission of radiation (not LaserJet) printers: Printing and hold the
Wireless
push button until the Attention light blinks. The printer might restart.
Any network settings on the printer are at present reset. Your printer remains in setup mode for 2 hours.
-
-
On your computer, open the HP Smart app.
-
If you lot are using the HP Smart app for the first fourth dimension, the app automatically searches for new printers.
-
If you have used the HP Smart app before, click the
Printers
tab.
-
-
Click
Set Up a New Printer, and then click
Continue.HP Smart searches for printers on your wireless network.
-
Select your printer, and and then click
Continue. -
When prompted, blazon the WEP or WPA cardinal (network password).
-
Afterward the printer connects to your wireless network, click
Go on, and so click
Go out Setup.In one case the printer is connected, the blue Wireless calorie-free stops blinking and remains on.
If the printer fails to connect to your wireless network, try another method.
Connect the printer with the HP Smart app (Android mobile device)
Use the HP Smart app to connect the printer to your wireless network.
-
Make sure your Android device is connected to the same wireless network that y’all want to connect your printer to.
-
Get to
123.hp.com
from a browser on your phone or tablet and install the HP Smart app. -
Plough on the printer. If the printer is in sleep mode, press the
Cancel
button on the control panel. -
Reset the printer network settings.
-
For near HP printers: Press and hold the
Wireless
and
Cancel
buttons until the Wireless and Power lights glimmer. -
For HP Green-eyed 6000, Pro 6400, DeskJet Plus IA 6000, and 6400 All-in-I printers: Press and hold the
Wireless
button on the back of the printer for five seconds until the Edge lighting flashes regal. It might take several attempts before the lighting flashes. -
For HP Tango printers: Press and concord the
Wireless
push button on the dorsum of the printer for five seconds until the front end lite flashes blue. -
For HP Light amplification by stimulated emission of radiation (not LaserJet) printers: Printing and agree the
Wireless
button until the Attention light blinks. The printer might restart.
Any network settings on the printer are now reset. Your printer remains in setup mode for two hours.
-
-
Whatsoever network settings on the printer are at present reset. Your printer remains in setup style for 2 hours.
-
Open up the HP Smart app, and then tap the
Plus sign
.
-
Tap
Add Printer.A listing of available printers displays.
-
Tap your printer. The printer proper name contains ‘Setup’ and the model number, such as
HP-Setup>A8-Deskjet 3700 series. -
Follow the on-screen instructions to type the WEP or WPA fundamental (network countersign).
-
After the printer connects to your wireless network, you lot tin skip the remaining screens to complete the setup.
Once the printer is continued, the blue Wireless light stops blinking and remains on.
If the printer fails to connect to your wireless network, try another method.
Connect the printer with the HP Smart app (iOS devices)
Use the HP Smart app to connect the printer to your wireless network.
-
Make sure your Apple iOS device is continued to the aforementioned wireless network that your printer is connected to, or that you desire to connect a new printer to.
-
Go to
123.hp.com
from a browser on your telephone or tablet and install the HP Smart app. -
Turn on the printer. If the printer is in sleep manner, press the
Cancel
push on the control panel. -
Reset the printer network settings.
-
For most HP printers: Press and hold the
Wireless
and
Cancel
buttons until the Wireless and Ability lights blink. -
For HP ENVY 6000, Pro 6400, DeskJet Plus IA 6000, and 6400 All-in-I printers: Press and concord the
Wireless
button on the back of the printer for five seconds until the Border lighting flashes imperial. It might accept several attempts earlier the lighting flashes. -
For HP Tango printers: Printing and hold the
Wireless
push button on the dorsum of the printer for v seconds until the front lite flashes blue. -
For HP Laser (not LaserJet) printers: Press and agree the
Wireless
button until the Attention light blinks. The printer might restart.
Any network settings on the printer are at present reset. Your printer remains in setup mode for ii hours.
-
-
Open the HP Smart app.
-
If a printer setup notification displays, tap the notification. Otherwise, tap the
Plus sign
to add your printer. -
Tap
Set up Upwards a New Printer. -
Press the
Domicile
push, and then connect your Apple device to your printer’s wireless network.-
From the home screen on your Apple device, tap
Settings, and and then tap
Wi-Fi. -
Tap your printer. The printer name contains ‘Setup’ and the model number, such as
HP-Setup>A8-Deskjet 3700 serial.Your Apple tree device is now on your printer’due south wireless network.
-
-
Printing the
Home
button, and and then tap the HP Smart app. -
Follow the on-screen instructions to blazon the WEP or WPA key (network countersign).
-
After the printer connects to your wireless network, you tin skip the remaining screens to complete the setup.
In one case the printer is connected, the blue Wireless lite stops blinking and remains on.
If the printer fails to connect to your wireless network, endeavour another method.
Connect the printer with a temporary USB connection (Windows)
Temporarily connect the printer to the computer with a USB cable, and then modify the connexion to wireless in HP Printer Assistant.
-
Search Windows for
HP, and and so click your printer name from the list of results. If you do not have the printer software installed on your computer, to become
123.hp.com
to download and install it.HP Printer Banana opens.
-
Click the
Utilities
tab. -
Click
Printer Setup & Software, and and then click
Reconfigure Wireless Settings. -
Follow the on-screen instructions to change the wireless settings.
-
When prompted, connect the USB cable and blazon the WEP or WPA key (network password).
Once the printer is connected, the blue Wireless light stops blinking and remains on.
If the printer fails to connect to your wireless network, try another method.
Connect the printer with a temporary USB connection (macOS)
Temporarily connect the printer to the Mac with a USB cablevision, and then change the connection to wireless in HP Utility.
-
Connect a USB cable to the USB port on the rear of the printer
and to the computer. -
Click the
Apple
carte du jour, then click
System Preferences. -
Depending on your Os version, click
Print & Scan
or
Printers & Scanners. -
Click the
Plus sign
, and so click
Add Printer or Scanner.
-
Click the name of your printer with
USB
under
Kind. -
On the
Use
menu, select the proper name of your printer, and then click
Add.annotation:
AirPrint is the default driver. To access all printer features, including HP Utility, select the HP printer proper noun.
-
Click the name of your printer, and and then click
Options & Supplies. -
Click
Utility, and then click
Open Printer Utility.
-
In HP Utility, click
Wireless Setup.
-
Make sure your network displays on the
Ostend Wireless Settings
window, and then click
Continue
to complete the wireless configuration.
-
If your network does not display
on the Confirm Wireless Settings window, connect to the right network.-
Select
No, I want to cull another network, and so click
Go on.A list of available wireless networks displays.
-
Select your wireless network from the list or type your network SSID in the
Wireless Network Name
field, and then type your network password in the
Password
field. -
Click
Continue.
-
-
Later the network connectedness is configured, click
Done, and and then disconnect the USB cable from the printer and the reckoner.In one case the printer is connected, the blue Wireless low-cal stops blinking and remains on.
-
In the Printers & Scanners or Impress & Scan window, click the name of your printer, click the
Minus sign
, and so delete the USB installed printer.
-
Click the
Plus sign
, and and then click
Add together Printer or Scanner. -
Click the proper noun of your printer with the text
Bonjour
listed under
Kind, click the
Use
or
Print Using
box, and and then select the proper name of your printer in the pop-up bill of fare. -
Click
Add
to add the printer to the listing.If the printer fails to connect to your wireless network, try another method.
Step 3: Impress a Wireless Network Test Report
Go to
HP Customer Support, select your printer model, and so search for “Printing Self-Examination Pages.” Print a Wireless Network Test Report, and and then follow any instructions on the report to troubleshoot wireless connectivity problems. For more than data, become to
Using a Wireless Network Test Written report.
If the wireless connection outcome persists, get to the
HP Wireless Print Centre
(in English) for more than information.